Extron electronic 1616 HV, HVA specification

LED key:

= off (value 0 dB), B = blinking (value 1dB),

= on (value 2dB)

					INPUTS
1	2	3	4	5	6	7	8	9	10	11	12

Press

E

RGBHV AUDIO

D B

CONTROL						I/O
CONTROL						I/O

1	2	3	4	5	6	7	8
			OUTPUTS

B

-1dB

ENTER PRESET VIEW

ESC

RGBHV AUDIO

D

D

(9 times)

VIEW

Figure 3-18 — Example 8, step d: Adjusting the audio level, CrossPoint Plus 84, 88, 124, and 128

				5		LED key:			= off (value 0dB),				B		= blinking,
				5					= on (value 1dB)
									= on (value 1dB)
								INPUTS
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
							OUTPUTS

D

-1dB

B D

	B
TROL	I/O
VIEW ESC	RGBHV AUDIO

Figure 3-19 — -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus 1616

If another input button is pressed and released, the level value for the current input is saved and level value for the newly selected input is displayed.

EPress and release the Audio button. The Audio LED stops blinking and the View () LED (if lit), the Esc () LED (if lit), the selected input LED, and all output LEDs turn off.

Both the RGBHV and Audio LEDs light.

Executive mode (front panel security lockout)

The executive mode limits the operation of the CrossPoint Plus switcher from the front panel. When the switcher is in executive mode, all of the front panel functions are disabled except for the view-only mode functions (see Viewing a configuration on page 3-9). Other than in view-only mode, if the user pushes a front panel button when the switcher is in executive mode, that button’s associated LED flashes twice and goes out.

To toggle executive mode on or off, press and hold the RGBHV and Audio buttons for approximately two seconds. The RGBHV and Audio LEDs blink twice to indicate the mode change. Release the RGBHV and Audio buttons. To toggle the executive mode state again, press and hold the RGBHV and Audio buttons again.

CrossPoint Plus Matrix Switchers • Operation 3-17

Image 37

Extron electronic 1616 HV, HVA manual Executive mode front panel security lockout

Contents

CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix Switchers Consignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad Español Quick Start CrossPoint Plus Matrix Switchers Save or recall a preset Quick Start CrossPoint Plus Matrix Switchers, cont’dView and adjust audio level Create a tie Table of Contents Table of Contents, cont’d One CrossPoint Plus Matrix Switchers Introduction About the CrossPoint Plus Series Matrix SwitchersIntroductiontroduction, cont’d CrossPoint Plus 128HVA Features Matrix Input Status Introduction, cont’d Audio gain and attenuation Any input to any or all outputs Two Rack Mounting the Switcher Installationstallation, cont’dPower connection CrossPoint Plus Matrix Switchers Installation Audio input and output connections HVA models only Video input and output connections RS-232/422 connection Installation, cont’d Rear panel view, CrossPoint Plus 84HV Additional rear panel views 11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three CrossPoint Plus Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d Definitions Control buttons and LEDs Input buttons, output buttons, and LEDs Controls Operation, cont’dFront panel I/O label windows Front Panel Operations PowerGrouping Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio ties Example 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tie Example 3, step d Removing an audio tie Viewing a configuration Rgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presets Example 7 Recall a preset Example 6 Save a preset Example 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only 17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockout System reset to factory defaults TroubleshootingRear Panel Controls General checks Worksheets Plasma display S-video problemWorksheet example 1 Entering system equipment Worksheet example 2 Drawing ties Worksheet example 3 Test configuration Preset # Matrix Switchers Configuration Worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’d Using the Command/Response Table Switcher Error Responses Command Ascii Command Response Additional description Command/Response TableProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Installing the software Matrix Switchers Control ProgramUsing the software MatrixSoftware,cont’d Windows buttons Extron Matrix Switcher+ Control Program window blank Windows menus Matrix Software, cont’d Using the help system Using emulation modeButton-Label Generator Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’d Audio input audio models only Audio audio models onlyAudio output audio models only Part Numbers Specifications, cont’dCrossPoint Plus part numbers Extron Part Cables Optional accessories Extron Part BNC-4 Mini HR Cable Pre-cut cables AppendixBB Opening the switcher Hardware UpgradesCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’d Figure B-2 Removing the front cover Reference Information, cont’d Closing the switcherSwapping the serial ports Figure B-4 Key and pin 1 mark Installing a firmware update Button Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA