Features, CrossPoint Plus 128HVA | Extron electronic 1616 HV

Monitor

CrossPoint Plus 128HVA

Projector

VSC 150

Projector

Up to 8 Outputs

VCR

RGB 109xi

RGB 103xi

RGB 112xi

Sun/SGI WorkstationPC ComputerMacintosh Computer

RGB 440	Up to 12 Inputs
Document Camera	Laptop w/ Audio Outputs
Document Camera

CVC 200	DVS 150	DVS 150
DVD Player	VCR	Laserdisc Player

Figure 1-1 — A typical CrossPoint Plus matrix switcher application

Features

Inputs — These switchers offer 8, 12, or 16 RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video, S-video, or composite video inputs on BNC connectors.

Stereo audio can be balanced or unbalanced, on 3.5 mm, 5-pole captive screw terminals (HVA models).

Outputs — 4, 8, or 16 RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video, S-video, or composite video outputs are available on BNC connectors.

Stereo audio, balanced or unbalanced, on 3.5 mm, 5-pole captive screw terminals (HVA models).

Bandwidth — The CrossPoint Plus Series provides a minimum of 425 MHz (-3dB) video bandwidth, fully loaded. Designed for resolutions from 1280 x 1024 and up, the CrossPoint Plus Series maintains original signal integrity. When the best matrix for your particular application is required, the

CrossPoint Plus Matrix Switchers • Introduction

1-3

Image 9

Extron electronic 1616 HV manual Features, CrossPoint Plus 128HVA

Contents

CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix Switchers Consignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad Español Quick Start CrossPoint Plus Matrix Switchers Save or recall a preset Quick Start CrossPoint Plus Matrix Switchers, cont’dView and adjust audio level Create a tie Table of Contents Table of Contents, cont’d One About the CrossPoint Plus Series Matrix Switchers CrossPoint Plus Matrix Switchers IntroductionIntroductiontroduction, cont’d CrossPoint Plus 128HVA Features Matrix Input Status Introduction, cont’d Audio gain and attenuation Any input to any or all outputs Two Rack Mounting the Switcher Installationstallation, cont’dPower connection CrossPoint Plus Matrix Switchers Installation Audio input and output connections HVA models only Video input and output connections RS-232/422 connection Installation, cont’d Rear panel view, CrossPoint Plus 84HV Additional rear panel views 11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three CrossPoint Plus Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d Definitions Control buttons and LEDs Input buttons, output buttons, and LEDs Operation, cont’d ControlsFront panel I/O label windows Power Front Panel OperationsGrouping Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio ties Example 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tie Example 3, step d Removing an audio tie Viewing a configuration Rgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presets Example 7 Recall a preset Example 6 Save a preset Example 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only 17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockout System reset to factory defaults TroubleshootingRear Panel Controls General checks Plasma display S-video problem WorksheetsWorksheet example 1 Entering system equipment Worksheet example 2 Drawing ties Worksheet example 3 Test configuration Preset # Matrix Switchers Configuration Worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’d Using the Command/Response Table Switcher Error Responses Command/Response Table Command Ascii Command Response Additional descriptionProgrammer’s Guide, cont’d Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Installing the software Matrix Switchers Control ProgramUsing the software MatrixSoftware,cont’d Windows buttons Extron Matrix Switcher+ Control Program window blank Windows menus Matrix Software, cont’d Using emulation mode Using the help systemButton-Label Generator Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’d Audio audio models only Audio input audio models onlyAudio output audio models only Part Numbers Specifications, cont’dCrossPoint Plus part numbers Extron Part Cables Optional accessories Extron Part BNC-4 Mini HR Cable Pre-cut cables AppendixBB Opening the switcher Hardware UpgradesCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’d Figure B-2 Removing the front cover Closing the switcher Reference Information, cont’dSwapping the serial ports Figure B-4 Key and pin 1 mark Installing a firmware update Button Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA