Windows buttons | Extron electronic 1616 HV, HVA specs

Figure 5-1 — Extron Matrix Switcher+ Control Program window (blank)

Figure 5-2 — Sample program window (complete)

4.To make the control program easier to use, assign a device icon to each input and output. Click on a box that represents an input or output, and drag the desired icon onto the box from the icon palette that appears.

5.To create a tie, drag an input box to one or more output boxes. To remove a tie, drag the output box to its tied input box.

6. For quick display of information on a specific input or output, place the cursor over that device in the control program window. The program pops up a window that details the connections to that device, the switching interval (RGB delay), and the frequency of the video signal input from or output to that device.

Windows buttons

The buttons on the right side of the window perform the following functions:

Power — Unavailable for CrossPoint Plus Series switchers, because the switcher power cannot be controlled via software.

CrossPoint Plus Matrix Switchers • Matrix Software

5-3

Image 53

Extron electronic 1616 HV, HVA manual Extron Matrix Switcher+ Control Program window blank, Windows buttons

Contents

CrossPoint Plus 84, 88, 124, 128, 168, and 1616 HV and HVA CrossPoint Plus Matrix Switchers Consignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad Español Quick Start CrossPoint Plus Matrix Switchers Save or recall a preset Quick Start CrossPoint Plus Matrix Switchers, cont’dView and adjust audio level Create a tie Table of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the CrossPoint Plus Series Matrix SwitchersCrossPoint Plus Matrix Switchers Introduction CrossPoint Plus 128HVA Features Matrix Input Status Introduction, cont’d Audio gain and attenuation Any input to any or all outputs Two Rack Mounting the Switcher Installationstallation, cont’dPower connection CrossPoint Plus Matrix Switchers Installation Audio input and output connections HVA models only Video input and output connections RS-232/422 connection Installation, cont’d Rear panel view, CrossPoint Plus 84HV Additional rear panel views 11 Rear panel view, CrossPoint Plus 124HV 15 Rear panel view, CrossPoint Plus 168HVA Installation, cont’d Three CrossPoint Plus Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d Definitions Control buttons and LEDs Input buttons, output buttons, and LEDs Front panel I/O label windows Operation, cont’dControls Grouping PowerFront Panel Operations Creating a configuration Example 2 Add a tie to a set of video and audio ties Example 1 Create a set of video and audio ties Example 3 Remove a tie from a set of video and audio ties Example 2 Adding a video tie Example 3, step d Removing an audio tie Viewing a configuration Rgbhv Audio View Muting and unmuting video and/or audio Example 5 Muting and unmuting an output 13 Example 5, step d Muting and unmuting outputs Using presets Example 7 Recall a preset Example 6 Save a preset Example 8 View and adjust an audio level Viewing and adjusting the input audio level HVA models only 17 +8dB displayed, CrossPoint Plus 168 19 -1dB displayed, CrossPoint Plus 168 and CrossPoint Plus Executive mode front panel security lockout System reset to factory defaults TroubleshootingRear Panel Controls General checks Worksheet example 1 Entering system equipment Plasma display S-video problemWorksheets Worksheet example 2 Drawing ties Worksheet example 3 Test configuration Preset # Matrix Switchers Configuration Worksheet Operation, cont’d Four Switcher-Initiated Messages Host-to-Switcher InstructionsCrossPoint Plus Matrix Switchers Programmer’s Guide Programmer’ser’sGuide,Guidecont’d Using the Command/Response Table Switcher Error Responses Programmer’s Guide, cont’d Command/Response TableCommand Ascii Command Response Additional description Command/response table for SIS commands Cont’d Video mute commands View ties, gain, mutes, and presets Programmer’s Guide, cont’d Five Installing the software Matrix Switchers Control ProgramUsing the software MatrixSoftware,cont’d Windows buttons Extron Matrix Switcher+ Control Program window blank Windows menus Matrix Software, cont’d Button-Label Generator Using emulation modeUsing the help system Extron’s Button-Label Generator window AAppendix a CrossPoint Plus Matrix Switchers Specifications Specificationsecifications, cont’d Audio output audio models only Audio audio models onlyAudio input audio models only Part Numbers Specifications, cont’dCrossPoint Plus part numbers Extron Part Cables Optional accessories Extron Part BNC-4 Mini HR Cable Pre-cut cables AppendixBB Opening the switcher Hardware UpgradesCrossPoint Plus Matrix Switchers Reference Information ReferenceInformation,co t’d Figure B-2 Removing the front cover Swapping the serial ports Closing the switcherReference Information, cont’d Figure B-4 Key and pin 1 mark Installing a firmware update Button Labels Figure B-5 Button label blanks, 16-button strip Reference Information, cont’d FCC Class a Notice Extron’s Warranty Extron Electronics, USA