Fairchild RC5051 specifications Introduction, Intel Pentium Pro Processor Power Requirements

www.fairchildsemi.com

Application Note 50

Implementing the RC5050 and RC5051 DC-DC Converters on Pentium® Pro Motherboards

Introduction

This document describes how to implement a switching volt- age regulator using an RC5050 or an RC5051 high speed controller, a power inductor, a Schottky diode, appropriate capacitors, and external power MOSFETs. This regulator forms a step down DC-DC converter that can deliver up to 14.5A of continuous load current at voltages ranging from 1.3V to 3.5V. A specific application circuit, design consider- ations, component selection, PCB layout guidelines, and per- formance evaluations are covered in detail.

Intel Pentium Pro Processor Power Requirements

Refer to Intel’s AP-523 Application Note, Pentium® Pro Processor Power Distribution Guidelines, November 1995 (order number 242764-001), as a basic reference. The speci- fications contained in this document have been modified slightly from the original Intel document to include updated specifications for more recent processors. Please contact Intel Corporation for specific details.

In the past 10 years, microprocessors have evolved at such an exponential rate that a modern chip can rival the computing power of a mainframe computer. Such evolution has been possible because of the increasing numbers of transistors that processors integrate. Pentium CPUs, for example, integrate well over 5 million transistors on a single piece of silicon.

To integrate so many transistors on a piece of silicon, their physical geometry has been reduced to the sub-micron level. As a result of each geometry reduction, the corresponding operational voltage for each transistor has also been reduced. The changing CPU voltage demands the design of a pro- grammable power supply—a design that is not completely re-engineered with every change in CPU voltage.

The voltage range of the CPU has shown a downwards trend for the past 5 years: from 3.3V for the Pentium, to 3.1V for the Pentium Pro, and to 1.8V for future processors. With this trend in mind, Raytheon Electronics has designed the RC5050 and RC5051 controllers. These controllers integrate the necessary programmability to address the changing power supply requirements of lower voltage CPUs.

Previous generations of DC-DC converter controllers were designed with fixed output voltages adjustable only with a set of external resistors. In a high volume production envi- ronment (such as with personal computers), however, a CPU voltage change requires a CPU board re-design to accommo- date the new voltage requirement. The 5-bit DAC in the RC5050 and the RC5051 reads the voltage ID code that is programmed into modern processors and provides the appro- priate CPU voltage. In this manner, the PC board does not have to be re-designed each time the CPU voltage changes. The CPU can thus automatically configure its own required supply voltage.

Input Voltages

Available inputs are +12V ±5% and +5V ±5%. Either one or both of these inputs can be used by the DC-DC converter. The input voltage requirements for Raytheon’s RC5050 and RC5051 DC-DC converters are listed in Table 1.

Table 1. Input Voltage Requirements

		MOSFET	MOSFET
Part #	Vcc for IC	Drain	Gate Bias
RC5050	+5V ±5%	+5V ±5%	12V ±5% or
RC5051			+5V ±5%

Pentium Pro DC Power Requirements

Refer to Table 2, Intel Pentium Pro and OverDrive® Proces- sor Power Specifications. For a motherboard designs without a standard VRM (Voltage Regulator Module) socket, the on-board DC-DC converter must supply a minimum of 13.9A of current @2.5V and 12.4A of current @3.3V. For a Flexible Motherboard design, the on-board DC-DC con- verter must supply 14.5A maximum ICCP.

DC Voltage Regulation

As indicated in Table 2, the voltage level supplied to the CPU must be within ±5% of its nominal setting. Voltage reg- ulation limits must include:

•Output load ranges specified in Table 2

•Output ripple/noise

•DC output initial voltage set point

•Temperature and warm up drift (Ambient +10°C to +50°C at full load with a maximum rate of change of 5°C per 10 minutes minimum but no more than 10°C per hour)

•Output load transient with:

Slew rate >30A/∝s at converter pins

Range: 0.3A - ICCP Max (as defined in Table 2).

Rev. 1.1.0