Programming Level One, Pan to Waste, 1234 | Frymaster BIELA14

4.11.5 Pan to Waste

4.11.5 Pan to Waste

Pan to waste selection is an option that allows bulk oil systems to pump excess oil in the pan to the bulk oil waste tanks without draining the existing oil in the frypot.

1.With the computer OFF, press and hold the filter button for the vat to be refilled for three seconds.

The computer displays filter menu for three seconds, changing to MAINT Filter.

2. Use the t and ubuttons to scroll to PAN TO WASTE.

3. With PAN TO WASTE displayed, press the (1 yes) button to continue.

The computer displays PAN TO WASTE? alternating with yes no.

4. Press the (yes) button and go to Section 4.10.4..3 page 4-18 and continue after step 6 or press (2 NO) button to exit to filter menu.

4.12 Programming Level One

Level one programming is used to enter new products, control when AIF (auto intermittent filtration) is disabled and perform deep clean (boil-out) and high-limit test.

To enter Level 1 programming mode:

1.With the computer OFF, press the TEMP and INFO buttons simultaneously for THREE seconds until LEVEL 1 is displayed; a chirp sounds.

The computer displays ENTER Code.

2. Enter 1234.

1

2

3

4

(1234)

The computer displays level 1 program for three seconds changing to Product

selection.

4-23

Image 41

Frymaster BIELA14 warranty Programming Level One, Pan to Waste, 1234, selection

Contents

FRYMASTER BIELA14 SERIES GEN II LOV OPERATOR’S MANUALELECTRIC FRYER FOR YOUR SAFETY NOTICE TO U.S. CUSTOMERS NOTICENOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS CANADA DANGER Adding New Product Menu Items Product Selection M3000 Menu Summary TreeSee section 4.10.2 B.WARRANTY PROVISIONS - FRYPOTS A.WARRANTY PROVISIONS - FRYERSD.WARRANTY EXCLUSIONS C.PARTS RETURN •overtime or holiday charges This warranty also does not cover BIELA14 SERIES GEN II LOV ELECTRIC FRYER 1.2Safety InformationCHAPTER 1: INTRODUCTION 1.1General 1.3Computer Information for the M3000 Computers 1.5Installation, Operating, and Service Personnel1.4European Community CE Specific Information CE Standard What to do if your equipment arrives damaged 1.7Shipping Damage Claim Procedure 1.8Service Information NOTICE 2.1General Installation Requirements 2.1.2 Electrical Grounding Requirements 2.1.3 Australian Requirements 2.2Power Requirements DANGER CHAPTER 3: OPERATING INSTRUCTIONS TYPICAL CONFIGURATION BIELA314 SHOWN M3000 COMPUTER 3.1Equipment Setup and Shutdown Procedures 3.3.2 Install the Oil Reservoir 3.3 Low Oil Volume Automatic Refill3.3.1 Prepare the System for Use 3.3.3 Routine Oil Changes 3.3.4Bulk Oil Systems FR FRIES 4.1M3000 General Information 4.2Basic Operation 4.3Cooking with Multi-ProductDisplay 4.4Cooking with Dedicated Display <<<< >>>> 4.5Changing from Breakfast Setup to Lunch<<<<>>>>; an alarm will sound Press and quickly 4.6Changing from Lunch Setup to Breakfast 4.7.1 Navigation Buttons 4.7M3000 Button Description and Functions4.7.2 Filter, Temperature and Info Buttons 4.7.3 Cook Channel and Selection Buttons See section 4.8M3000 Menu Summary Tree4.10.2 4.10.3 1234 4.9Fryer Setup Mode Programming 24hR 4.10.1 Escape Menu Items 4.10 M3000 Common Tasksfull 1.Escaping out of a menu or sub-menu PROD selectionproduct COOK ID DISABLE Product selection prompt 4.10.3 Storing Menu Items in Product Buttons 4.10.4.1 Disposal for Non-BulkOil Systems 4.10.4.2 Refilling JIB Oil Systems 2. Press the u INFO button and scroll to dispose When finished, the computer displays REMOVE PAN4. To dispose press the 1 yes button to continue The computer displays DRAINING 4.11 Filter Menu 4.11.1 Accessing the Filter Menua. auto filter b. maint filter 4.11.2 Drain to Pan yes no 4.11.3 Fill Vat from Drain Pan 4.11.4 Fill Vat from Bulk 4.11.5 Pan to Waste 4.12 Programming Level One e. Fryer setup c. DEEP CLEAN MODEa.disabled b.enabled 4.12.1 AIF CLOCK Yes No 4.12.2DEEP CLEAN MODE BOIL-OUTselection display EMPTY? and Yes NO DANGER 4.12.3 HIGH-LIMITTEST MODE comp 4.13 Programming Level Two 4.13.1 PRODUCT COMP MODE c. password SETUPa. Prod comp b. e-log 4.13.2 E-LOGMODE 4.13.3 PASSWORD SETUP MODE 4.13.4 ALERT TONE MODE 4.13.5 FILTER AFTER 4.13.6 FILTER TIME 4.14 INFO Mode SPLIT VAT CONFIGURATION FULL VAT CONFIGURATION4.14.1 FILTER STATS MODE a. filter stats a. DAY wed, DATE 03/20/07 – Current day and date 4.14.2 REVIEW USAGE MODE 4.14.3LAST LOAD MODE FULL / SPLIT VAT CONFIGURATION4321 4-38 5.Press the 2 button again to quit 5.1Introduction CHAPTER 5: FILTRATION INSTRUCTIONSThe filter pad or paper MUST be replaced daily 5.2Preparing the Filter for Use 5.3 Auto Intermittent Filtration AIF 5.3.1 Auto Demand Filtration DRAINING, WASHING and FILLING during the process 2. Press the 9 1 yes button to continue 9.Press 9 1 yes to silence alarm and continue prompt for SYSTEM ERROR 5.4.4 Filter Error Flowchart The filter pad or paper must be replaced daily 5.4.5 Filter Busy5.5Manual or End of Day Filtration MAINT FLTR 2.Press the uINFO button to scroll to maInT fIltEr 9. Press the 9 1 yes button to continue 6.1.3Clean Behind Fryers – Weekly 6.1Cleaning the Fryer DANGER6.1.2Clean the Built-inFiltration System – Daily Replace the O-rings Deep Clean Boiling Out the Frypot6.2Annual/Periodic System Inspection Fryer Built-InFiltration System 7.1 Introduction Problem Problem7.2Troubleshooting 7.2.1 Computer and Heating Problems 7.2.3 Filtration Problems Corrective Action 7.2.4 Auto Top-OffProblems Error Log Codes 7.2.5 Bulk Oil System ProblemsProbable Causes 7.2.6 is missing 8.1Wiring Diagrams 8.1.1Component Wiring Domestic CHAPTER 8: WIRING DIAGRAMS 8.1.2Component Wiring CE 8.1.3Component Wiring CSA 8.1.4Component Wiring Australia 8.1.5Contactor Box – Delta Configuration 8.1.6 Contactor Box – WYE Configuration 8051734Q 8.1.7 BIELA14 Series GEN II LOV Simplified WiringSTART OF 6-WIRE DATA & POWER Page NOTE: Do NOT overfill the jug A.1.1 Bulk Oil Systems Figure 2: Position the melter APPENDIX C: Solid Shortening Melter Use FAX Parts SERVICE HOTLINEFAX Tech Support 1-800-551-8633