Probable Causes, Bulk Oil System Problems | Frymaster BIELA14

7.2.5 Bulk Oil System Problems

7.2.5 Bulk Oil System Problems

Problem

Probable Causes

	A.	Incorrect setup procedure.
JIB won’t fill.	B.	Another function is in process.
	C.	Dispose valve not completely closed.
	D.	Bulk oil tank is empty.
	E.	Solenoid, pump or switch issue.

JIB or vat filling slow.	A. Pump or line issues beyond the scope
	of operator troubleshooting.

A.Incorrect setup procedure.

Frypot won’t fill. B. Dispose valve not completely closed.

C.Bulk oil tank is empty.

D.RTI pump issue.

Corrective Action

A.Power cycle fryer by disconnecting and reconnecting 5-pin control power cord.

B.If a filtration or any other filter menu function is in process or

FILTER NOW? YES/NO, CONFIRM YES/NO, or SKIM VAT are displayed, wait until the process is complete and try again.

C.Ensure the dispose valve handle is pushed fully closed.

D.Call your bulk oil provider.

E.Call you ASA for assistance.

A.Contact your bulk oil provider.

A.Power cycle fryer by disconnecting and reconnecting 5-pin control power cord.

B.Ensure the dispose valve handle is pushed fully closed.

C.Call your bulk oil provider.

D.Call you ASA for assistance.

7.2.6	Error Log Codes

Code		ERROR MESSAGE	EXPLANATION
E01		REMOVE DISCARD (Right)	A product cook is started on the right side of a
			split vat or in a full vat that has a different
			setpoint other than the current vat temperature.
E02		REMOVE DISCARD (Left)	A product cook is started on the right side of a
			split vat or in a full vat that has a different
			setpoint other than the current vat temperature.
E03		ERROR TEMP PROBE FAILURE	TEMP Probe reading out of range
E04		HI 2 BAD	High limit reading is out of range.
E05		HOT HI 1	High limit temperature is past more than 410°F
			(210°C), or in CE countries, 395°F (202°C)
E06		HEATING FAILURE	A component has failed in the high limit circuit
			such as computer, interface board, contactor or
			open-high limit.
E07		ERROR MIB SOFTWARE	Internal MIB software error
E08		ERROR ATO BOARD	MIB detects ATO board connection lost; ATO
			board failure
E09		ERROR PUMP NOT FILLING	Dirty pad and it needs changed or it was
			bypassed; filter pump problem
E10		ERROR DRAIN VALVE NOT OPEN	Drain valve was trying to open and confirmation
			is missing
E11		ERROR DRAIN VALVE NOT CLOSED	Drain valve was trying to close and confirmation

7-5

Image 73

Frymaster BIELA14 Probable Causes, Bulk Oil System Problems, 7.2.6, Error Log Codes, Explanation, Corrective Action

Contents

FRYMASTER BIELA14 SERIES GEN II LOV OPERATOR’S MANUALELECTRIC FRYER FOR YOUR SAFETY NOTICE TO U.S. CUSTOMERS NOTICENOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS CANADA DANGER Adding New Product Menu Items Product Selection M3000 Menu Summary TreeSee section 4.10.2 B.WARRANTY PROVISIONS - FRYPOTS A.WARRANTY PROVISIONS - FRYERSD.WARRANTY EXCLUSIONS C.PARTS RETURN •overtime or holiday charges This warranty also does not cover BIELA14 SERIES GEN II LOV ELECTRIC FRYER 1.2Safety InformationCHAPTER 1: INTRODUCTION 1.1General 1.3Computer Information for the M3000 Computers 1.5Installation, Operating, and Service Personnel1.4European Community CE Specific Information CE Standard What to do if your equipment arrives damaged 1.7Shipping Damage Claim Procedure 1.8Service Information NOTICE 2.1General Installation Requirements 2.1.2 Electrical Grounding Requirements 2.1.3 Australian Requirements 2.2Power Requirements DANGER CHAPTER 3: OPERATING INSTRUCTIONS TYPICAL CONFIGURATION BIELA314 SHOWN M3000 COMPUTER 3.1Equipment Setup and Shutdown Procedures 3.3.2 Install the Oil Reservoir 3.3 Low Oil Volume Automatic Refill3.3.1 Prepare the System for Use 3.3.3 Routine Oil Changes 3.3.4Bulk Oil Systems FR FRIES 4.1M3000 General Information 4.2Basic Operation 4.3Cooking with Multi-ProductDisplay 4.4Cooking with Dedicated Display <<<< >>>> 4.5Changing from Breakfast Setup to Lunch<<<<>>>>; an alarm will sound Press and quickly 4.6Changing from Lunch Setup to Breakfast 4.7.1 Navigation Buttons 4.7M3000 Button Description and Functions4.7.2 Filter, Temperature and Info Buttons 4.7.3 Cook Channel and Selection Buttons See section 4.8M3000 Menu Summary Tree4.10.2 4.10.3 1234 4.9Fryer Setup Mode Programming 24hR 4.10.1 Escape Menu Items 4.10 M3000 Common Tasksfull 1.Escaping out of a menu or sub-menu product selectionPROD COOK ID DISABLE Product selection prompt 4.10.3 Storing Menu Items in Product Buttons 4.10.4.1 Disposal for Non-BulkOil Systems 4.10.4.2 Refilling JIB Oil Systems 2. Press the u INFO button and scroll to dispose When finished, the computer displays REMOVE PAN4. To dispose press the 1 yes button to continue The computer displays DRAINING 4.11 Filter Menu 4.11.1 Accessing the Filter Menua. auto filter b. maint filter 4.11.2 Drain to Pan yes no 4.11.3 Fill Vat from Drain Pan 4.11.4 Fill Vat from Bulk 4.11.5 Pan to Waste 4.12 Programming Level One e. Fryer setup c. DEEP CLEAN MODEa.disabled b.enabled 4.12.1 AIF CLOCK selection display 4.12.2DEEP CLEAN MODE BOIL-OUTYes No EMPTY? and Yes NO DANGER 4.12.3 HIGH-LIMITTEST MODE comp 4.13 Programming Level Two 4.13.1 PRODUCT COMP MODE c. password SETUPa. Prod comp b. e-log 4.13.2 E-LOGMODE 4.13.3 PASSWORD SETUP MODE 4.13.4 ALERT TONE MODE 4.13.5 FILTER AFTER 4.13.6 FILTER TIME 4.14 INFO Mode SPLIT VAT CONFIGURATION FULL VAT CONFIGURATION4.14.1 FILTER STATS MODE a. filter stats a. DAY wed, DATE 03/20/07 – Current day and date 4.14.2 REVIEW USAGE MODE 4321 FULL / SPLIT VAT CONFIGURATION4.14.3LAST LOAD MODE 4-38 5.Press the 2 button again to quit 5.1Introduction CHAPTER 5: FILTRATION INSTRUCTIONSThe filter pad or paper MUST be replaced daily 5.2Preparing the Filter for Use 5.3 Auto Intermittent Filtration AIF 5.3.1 Auto Demand Filtration DRAINING, WASHING and FILLING during the process 2. Press the 9 1 yes button to continue 9.Press 9 1 yes to silence alarm and continue prompt for SYSTEM ERROR 5.4.4 Filter Error Flowchart 5.5Manual or End of Day Filtration MAINT FLTR 5.4.5 Filter BusyThe filter pad or paper must be replaced daily 2.Press the uINFO button to scroll to maInT fIltEr 9. Press the 9 1 yes button to continue 6.1.2Clean the Built-inFiltration System – Daily 6.1Cleaning the Fryer DANGER6.1.3Clean Behind Fryers – Weekly Replace the O-rings Deep Clean Boiling Out the Frypot6.2Annual/Periodic System Inspection Fryer Built-InFiltration System 7.1 Introduction Problem Problem7.2Troubleshooting 7.2.1 Computer and Heating Problems 7.2.3 Filtration Problems Corrective Action 7.2.4 Auto Top-OffProblems Error Log Codes 7.2.5 Bulk Oil System ProblemsProbable Causes 7.2.6 is missing 8.1Wiring Diagrams 8.1.1Component Wiring Domestic CHAPTER 8: WIRING DIAGRAMS 8.1.2Component Wiring CE 8.1.3Component Wiring CSA 8.1.4Component Wiring Australia 8.1.5Contactor Box – Delta Configuration 8.1.6 Contactor Box – WYE Configuration START OF 6-WIRE DATA & POWER 8.1.7 BIELA14 Series GEN II LOV Simplified Wiring8051734Q Page NOTE: Do NOT overfill the jug A.1.1 Bulk Oil Systems Figure 2: Position the melter APPENDIX C: Solid Shortening Melter Use FAX Parts SERVICE HOTLINEFAX Tech Support 1-800-551-8633