Manuals / Frymaster / Kitchen Appliance / Fryer

Frymaster H14SC, H17SC, H22SC manual Oil Return System Components

Models: H14SC H22SC H17SC

1 74

Page 71

8.7Oil Return System Components

	23
	22
	21
		18
		17
	20
19		16
19
		15
		7
5	11	12
13		14
		14
		6
		10
	8
9
		4
		3
		2
		1
		8-26

Page 71

Image 71

Frymaster H14SC, H17SC, H22SC manual Oil Return System Components

Contents

8196004 24-Hour Service HotlineandPartsManualService,Operation,Installation FRYERSDANGER DANGERDANGER DANGERCANADA Never spray the fryer with water or use water jets to clean the fryerNOTICE TO U.S. CUSTOMERS NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS U.SNavy Surface Ship Electric Fryers Installation, Operation, Service, and Parts Manual TABLE OF CONTENTSDANGER 1.2 Safety InformationNAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 1 INTRODUCTION 1.1 GeneralRETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE 1.4 Shipping Damage Claim Procedure1.5 Service Information 1.3 Controller InformationDANGER NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 2 INSTALLATION INSTRUCTIONS2.1 Introduction Do not block the area around the base or under the fryersThe contacts CANNOT have an external voltage applied 2.2 Power RequirementsDo not connect the contacts in series Do not connect more than one fryer to each set of contactsDANGER 2.3 Installation2.5 Dimensions and Weights 2.4 After Fryers Are Anchored At the Frying Station DANGERBACK OF FRYER UNIT 2-Fryer BatterySingle Fryer FRONT HANDLE62.55 3-Fryer Battery4-Fryer Battery 2.470DANGER 3.1 Equipment Setup and Shutdown ProceduresNAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 3 OPERATING INSTRUCTIONS DANGERDESCRIPTION 3.2 Operation of the Solid-State Analog ControllerShutdown DANGER properly filled with oil. See Section CONTROLLER OPERATING PROCEDUREHIGH-LIMIT TEST PROCEDURE The analog controller has no timing features. The operator must monitor shake and pull times5. Place the controller power switch in the OFF position 4.2 Preparing the Filter for Use NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 4 FILTRATION INSTRUCTIONS4.1 Introduction DANGER 4.3 Operation of the Filter DANGER3. Place the metal filter screen in the center of the bottom of the pan, then lay a sheet of filter paper on top of the screen, over- lapping on all sides DANGER 2. Remove the basket support rack from the frypot, raise the element assembly to the up position, and snap the Power Shower into positionDANGER DANGERDANGER 4.4 Draining and Disposing of Waste Oil6. Lower the elements into the frypot and reinstall the basket support rack. Ensure the drain valve is fully closed. If the drain valve is not fully closed, the fryer will not operate. Turn the fryer ON and allow the cooking oil to reach setpoint DANGER5.1.2 Clean the Built-in Filtration System - Daily NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 5 PREVENTIVE MAINTENANCE5.1 Cleaning the Fryer DANGER 5.1.1 Clean Inside and Outside of the Fryer Cabinet - DailyDANGER 5.1.3 Clean the Frypot and Heating Elements - Weekly DANGERBoiling-Out the Frypot 2. Press the fryer ON/OFF switch to the ON positionDANGER 5.1.4 Clean Detachable Parts and Accessories - Weekly5.2 Check Calibration of Temperature Control Knob - Monthly 5. Turn the fryer ON/OFF switchs to the OFF positionBuilt-In Filtration System 5.3 Annual/Periodic System InspectionFryer Check filtration system integrity as follows − Verify that filter pan cover is present and properly installedVerify that frypot drain valves are fully closed NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 6 OPERATOR TROUBLESHOOTING6.1 Introduction Verify that power is connected and that circuit breakers are onCorrective Action Problem6.2 Troubleshooting 6.2.1 Control and Heating Problems Probable CausesProbable Causes ProblemCorrective Action Problem 6.2.2 Error Messages and Display Problems6.2.3 Filtration Problems ProblemFilter pump runs ProblemProbable Causes Corrective Action6.3 Replacing the Controller or Controller Wiring Harness 7.2 Replacing a Controller NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 7 SERVICE PROCEDURES7.1 General 7.3 Replacing Component Box Components DANGER 7.4 Replacing a Temperature Probe or High-Limit ThermostatDO NOT drain more than one full frypot into the SDU at one time 1. Remove the filter pan and lid from the unit. Drain the frypots into a Shortening Disposal Unit SDU or other appropriate container7.5 Replacing a Heating Element viewed from the rear DO NOT drain more than one full frypot into the SDU at one time 7.6 Replacing Contactor Box Components7.7 Replacing a Frypot DANGER12. Disconnect the oil return flexlines at the frypot ends 22. Reinstall the drain tube assembly Sediment Particle Oil Flow Up for reverse Down for forward 7.8.2 Replacing the Filter Motor, Filter Pump, and Related ComponentsDANGER DO NOT drain more than one full frypot into the SDU at one time7-10 7.8.3 Replacing the Filter Transformer or Filter Relay Test 7.9 Interface Board Diagnostic ChartDiagnostic LED Legend Meter Setting8051421F 7.10 Wiring Diagram, SystemRefer to page 2-2 for power requirements 7-137-14 7.11 Wiring Diagram, Contactor BoxRefer to page 2-2 for power requirements 7.12 Components Description of Operation Accessories NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 8 PARTS LIST8.2 Cabinetry 106-3036SP Side, Cabinet Single Left Use 212-8479 for Rt. SideHandle Grab Rail For handle end use Top Cap Single Top cap for five station fryer shown8.2.2 Cabinet Bases, Braces, and Associated Parts 8.2.2 Cabinet Bases, Braces, and Associated Parts cont Upright Assembly, Left Use 106-3828 for singlesUpright Assembly, Right Use 106-3829 for singles Channel, Base Rear Use 106-4901 for singles base assembly8.3.1 Drain Tube Sections and Associated Parts 8.3 Drain System ComponentsValve Detail 8.3.1.1 Euro-Look Drain Tube Section and Associated PartsSee Page 8-10 for Drain EURO-LOOK 8.3.1.1 Euro-Look Drain Tube Section and Associated Parts cont8.3.2 Drain Valve Assembly and Component Parts Page ITEM EURO-LOOK PART # 8.4 Electronics and Wiring Components 8.4.1.1 Single Component BoxCOMPONENT PART #8.4.1.2 Multiple Vat Component Boxes PART # 8.4.2.1 Single Contactor BoxCOMPONENT PART #8.4.2.2 Multiple Vat Contactor Boxes 8.4.3 Heating Element Assembly and Associated Parts PART # 8.4.3 Heating Element Assembly and Associated Parts contCOMPONENT PART #8.4.4 Wiring8.4.5.1 Contactor Box Wiring Assembly - 12-Pin Full-Vat C-1 8.4.5.2 Contactor Box Wiring Assemblies - 6-Pin Left ElementP/N 106-3467SP 14/17kW or P/N 106-2472SP 22kW 8.4.5.3 Contactor Box Wiring Assemblies - 9-Pin Right Element8.4.5.4 Single Contactor Box Wiring Assembly 8.4.5.5 Main Wiring Harness8.4.5.9 Single Component Box Wiring Harness - 15-Pin without Filter 8.4.5.6 Single Main Wiring Harness8.4.5.7 Component Box Wiring Harness - 15-Pin 8.4.5.8 Single Component Box Wiring Harness - 15-Pin8.5.1 FPH117/122 Filtration Components 8.5 Filtration System Components8.5.1 FPH117/122 Filtration Components cont NOTE Some early production 8.5.2 FPH217/317 Multiple Battery Filtration System Componentsunits were configured this way Lid for units built before Feb 04, use 8.5.2 FPH217/317 Multiple Battery Filtration System Components contSTANDARD EURO-LOOKThermostat P/N 8.6 Frypot Assembly and ThermostatFrypot P/N 823-2451SP 8.7 Oil Return System Components PART # 8.7 Oil Return System Components contCOMPONENT PART #COMPONENT 8.8 WIRING CONNECTORS, PIN TERMINALS, AND POWER CORDSPower Cords ConnectorsTech Support SERVICE HOTLINEShipping Address 8700 Line Avenue, Shreveport, Louisiana FAX Parts