Frymaster H17SC, H22SC, H14SC manual

6.3Replacing the Controller or Controller Wiring Harness

6.3Replacing the Controller or Controller Wiring Harness

1.Disconnect the fryer from the electrical supply. For fryers that have 90º-angle topcaps, remove the two screws in the upper corners of the control panel and swing the panel open from the top, allowing it to rest on its hinge tabs. The bezel on fryers with rounded topcaps is held in place by tabs at the top and bottom. Slide the bezel up to disengage the lower tabs. Then slide the bezel down to disengage the upper tabs. Remove the top two screws holding the controller to the control panel frame. The controller will hinge down to access the 15-pin connector on the back.

2.Disconnect the wiring harness from the back of the controller. If replacing the harness, disconnect it from the interface board. If replacing the controller, disconnect the ground wire and remove the controller by lifting it from the hinge slots in the control panel frame.

3.Reverse the procedure to install a new controller or wiring harness.

15-Pin Connector	Ground Wire Terminal

6-6

Image 30

Frymaster H17SC, H22SC, H14SC manual Replacing the Controller or Controller Wiring Harness

Contents

FRYERS 24-Hour Service HotlineandPartsManualService,Operation,Installation 8196004 DANGER NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS U.S Never spray the fryer with water or use water jets to clean the fryerNOTICE TO U.S. CUSTOMERS CANADA Installation, Operation, Service, and Parts Manual TABLE OF CONTENTS Navy Surface Ship Electric Fryers 1.2 Safety Information NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 1 INTRODUCTION1.1 General 1.3 Controller Information 1.4 Shipping Damage Claim Procedure1.5 Service Information RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 2 INSTALLATION INSTRUCTIONS 2.1 IntroductionDo not block the area around the base or under the fryers Do not connect more than one fryer to each set of contacts 2.2 Power RequirementsDo not connect the contacts in series The contacts CANNOT have an external voltage applied 2.3 Installation 2.5 Dimensions and Weights2.4 After Fryers Are Anchored At the Frying Station DANGER FRONT HANDLE 2-Fryer BatterySingle Fryer BACK OF FRYER UNIT 2.470 3-Fryer Battery4-Fryer Battery 62.55 3.1 Equipment Setup and Shutdown Procedures NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 3 OPERATING INSTRUCTIONS 3.2 Operation of the Solid-State Analog Controller ShutdownDESCRIPTION properly filled with oil. See Section CONTROLLER OPERATING PROCEDURE HIGH-LIMIT TEST PROCEDUREThe analog controller has no timing features. The operator must monitor shake and pull times 5. Place the controller power switch in the OFF position NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 4 FILTRATION INSTRUCTIONS 4.1 Introduction4.2 Preparing the Filter for Use 4.3 Operation of the Filter DANGER 3. Place the metal filter screen in the center of the bottom of the pan, then lay a sheet of filter paper on top of the screen, over- lapping on all sides 2. Remove the basket support rack from the frypot, raise the element assembly to the up position, and snap the Power Shower into position 4.4 Draining and Disposing of Waste Oil 6. Lower the elements into the frypot and reinstall the basket support rack. Ensure the drain valve is fully closed. If the drain valve is not fully closed, the fryer will not operate. Turn the fryer ON and allow the cooking oil to reach setpoint 5.1.1 Clean Inside and Outside of the Fryer Cabinet - Daily NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 5 PREVENTIVE MAINTENANCE5.1 Cleaning the Fryer DANGER 5.1.2 Clean the Built-in Filtration System - Daily 5.1.3 Clean the Frypot and Heating Elements - Weekly DANGER Boiling-Out the Frypot2. Press the fryer ON/OFF switch to the ON position 5.1.4 Clean Detachable Parts and Accessories - Weekly 5.2 Check Calibration of Temperature Control Knob - Monthly5. Turn the fryer ON/OFF switchs to the OFF position 5.3 Annual/Periodic System Inspection FryerBuilt-In Filtration System − Verify that filter pan cover is present and properly installed Check filtration system integrity as follows Verify that power is connected and that circuit breakers are on NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 6 OPERATOR TROUBLESHOOTING6.1 Introduction Verify that frypot drain valves are fully closed Probable Causes Problem6.2 Troubleshooting 6.2.1 Control and Heating Problems Corrective Action Probable Causes 6.2.2 Error Messages and Display Problems 6.2.3 Filtration Problems Filter pump runs 6.3 Replacing the Controller or Controller Wiring Harness NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 7 SERVICE PROCEDURES 7.1 General7.2 Replacing a Controller 7.3 Replacing Component Box Components 7.4 Replacing a Temperature Probe or High-Limit Thermostat DO NOT drain more than one full frypot into the SDU at one time1. Remove the filter pan and lid from the unit. Drain the frypots into a Shortening Disposal Unit SDU or other appropriate container 7.5 Replacing a Heating Element viewed from the rear 7.6 Replacing Contactor Box Components 7.7 Replacing a Frypot 12. Disconnect the oil return flexlines at the frypot ends 22. Reinstall the drain tube assembly 7.8.2 Replacing the Filter Motor, Filter Pump, and Related Components Sediment Particle Oil Flow Up for reverse Down for forward 7-10 7.8.3 Replacing the Filter Transformer or Filter Relay Meter Setting 7.9 Interface Board Diagnostic ChartDiagnostic LED Legend Test 7-13 7.10 Wiring Diagram, SystemRefer to page 2-2 for power requirements 8051421F 7.11 Wiring Diagram, Contactor Box 7-14 7.12 Components Description of Operation NAVY SURFACE SHIP ELECTRIC FRYERS CHAPTER 8 PARTS LIST Accessories 8.2 Cabinetry Top Cap Single Top cap for five station fryer shown Side, Cabinet Single Left Use 212-8479 for Rt. SideHandle Grab Rail For handle end use 106-3036SP 8.2.2 Cabinet Bases, Braces, and Associated Parts Channel, Base Rear Use 106-4901 for singles base assembly Upright Assembly, Left Use 106-3828 for singlesUpright Assembly, Right Use 106-3829 for singles 8.2.2 Cabinet Bases, Braces, and Associated Parts cont 8.3 Drain System Components 8.3.1 Drain Tube Sections and Associated Parts 8.3.1.1 Euro-Look Drain Tube Section and Associated Parts See Page 8-10 for DrainValve Detail 8.3.1.1 Euro-Look Drain Tube Section and Associated Parts cont EURO-LOOK 8.3.2 Drain Valve Assembly and Component Parts Page ITEM EURO-LOOK 8.4 Electronics and Wiring Components 8.4.1.1 Single Component Box 8.4.1.2 Multiple Vat Component Boxes 8.4.2.1 Single Contactor Box 8.4.2.2 Multiple Vat Contactor Boxes 8.4.3 Heating Element Assembly and Associated Parts 8.4.3 Heating Element Assembly and Associated Parts cont 8.4.5.2 Contactor Box Wiring Assemblies - 6-Pin Left Element Wiring8.4.5.1 Contactor Box Wiring Assembly - 12-Pin Full-Vat C-1 8.4.4 8.4.5.5 Main Wiring Harness 8.4.5.3 Contactor Box Wiring Assemblies - 9-Pin Right Element8.4.5.4 Single Contactor Box Wiring Assembly P/N 106-3467SP 14/17kW or P/N 106-2472SP 22kW 8.4.5.8 Single Component Box Wiring Harness - 15-Pin 8.4.5.6 Single Main Wiring Harness8.4.5.7 Component Box Wiring Harness - 15-Pin 8.4.5.9 Single Component Box Wiring Harness - 15-Pin without Filter 8.5 Filtration System Components 8.5.1 FPH117/122 Filtration Components 8.5.1 FPH117/122 Filtration Components cont 8.5.2 FPH217/317 Multiple Battery Filtration System Components units were configured this wayNOTE Some early production EURO-LOOK 8.5.2 FPH217/317 Multiple Battery Filtration System Components contSTANDARD Lid for units built before Feb 04, use 8.6 Frypot Assembly and Thermostat Frypot P/N 823-2451SPThermostat P/N 8.7 Oil Return System Components 8.7 Oil Return System Components cont Connectors 8.8 WIRING CONNECTORS, PIN TERMINALS, AND POWER CORDSPower Cords COMPONENT FAX Parts SERVICE HOTLINEShipping Address 8700 Line Avenue, Shreveport, Louisiana Tech Support