Fujitsu IP-9610 manual

IP-9610

Hardware User’s Guide

Contents

Page Page USING IP-9610SAFELY Handling of This Manual IMPORTANT NOTE TO USERS All Rights Reserved. Copyright © FUJITSU LIMITED PREFACE ORGANIZATION AND CONTENTS OF THIS MANUAL WARNING INDICATIONS Warning indications within text SAFETY PRECAUTIONS List of important warnings Normal use Possibility of electric shock and fire Possibility of electric shock and fire Possibility of electric shock Possibility of electric shock, fire, and damage to the device Possibility of serious injury and damage to the device Possibility of fire, serious injury and damage to the device LABEL PRODUCT HANDLING PRECAUTIONS Maintenance Connectable devices Disposal Modification and restoration CONTENTS Help Information 5.3.2 Change of maintenance parts (Maintenance only) A.1 A.2 A.2.1 CHAPTER PREPARATIONS Page 1.1.1 Main Features Hardware option Maximum Description installation *1 The codec board has an 8 channel audio function 1.21.2 Components 1.31.3 Basic Application Examples 1.41.4 Part Names explanation. For more information, see Software guide DVB-ASIinput terminal. 75Ω unbalanced DVB-ASIinput See Section 2.4, “Connection to DVB-ASIDevice”, for an explanation on (DVB-ASIIN) using this terminal Page INSTALLATION AND CONNECTION Page 2.12.1 Installation Conditions 2.1.1 Environment conditions 2.1.2 Installation environment 1. 19” rack mounting Page 2. Desk-topinstallation Mark for rubber feet 2.1.3 Air flow into and out from the device 2.1.4 Open space required around the device 2.2 Power Supply System Connections 2.2.1 Connection to ground 2.2.2 Connection to power source AC cable clamp USABLE DETACHABLE POWER SUPPLY CABLE SET ASA Possibility of electric shock, fire, and damage to the device Possibility of damage to the device 100-240VAC 2.32.3 Connection to External Sync(REF) 2.42.4 Connection to DVB-ASIDevice 2.4.1 Connection to DVB-ASIInput Device 2.4.2 Connection to DVB-ASIOutput Device 2.5Connection to RS-232C/RS-422 2.5Device 2.62.6 Connection to Network HUB, Router, etc 2.7Connection to Voice 2.7Communication (Intercom) 2.82.8 Optional Board Slot OPERATION INSTRUCTIONS Page 3.13.1 Power ON/OFF 3.1.1 Powering on 3.1.2 Powering off 3.23.2 Device Settings and Operation 3.3 Device Settings and Operation (Front Panel) 3.43.4 Special Use of Cancel Key CABLE SPECIFICATIONS Page 4.14.1 Installation Preparations 4.24.2 Cable and Connector Details (3)RS-232C / RS-422cable (3) RS-232C RS-232CDTE RS-232CDCE (4) LAN cable (8) Intercom adapter cable Front view ・Audio adapter cable Type 1 TA75959-XXXXType 2 TA75960-XXXX (9) 100 - 240 VAC power cord Page Page TROUBLESHOOTING Page 5.15.1 Help Information Table 5.1 Problem descriptions and recommended actions Page 5.25.2 Alarm LED Lamp Is On Table 5.2 LED display details 5.35.3 Maintenance 5.3.1 Maintenance space Flont space for maintenance > 700×1000 mm Rear space 5.3.2 Change of maintenance parts (Maintenance only) Page Appendix Page A.A1.1 Appearance 500±4 mm 43±1.5 mm 425±4 mm Page A.A2.2 Basic Specifications A.2.1 External specifications A.2.2 Environment specifications A.2.3 Function specifications Page Parallel 2 pin with ground G: Green, O: Orange, R: Red A.A3.3 Preparations for Installation Work A.3.1 Scope of installation work A.3.2 Unpacking and device check A.3.3 Installation conditions A.3.4 Connecting external cables A.4 Preparations for On-site Turn-up (1)Preparations (1) (2)Environment check (2) (3)Visual check of appearance (6)Power on (6) (7)Unit test (7) Since this device executes a Page Glossary and Index Page Glossary IP (Internet Protocol) IP Address IP Multicast LAN (Local Area Network) LED (Light-EmittingDiode) TS (Transport Stream) TTL (Time To Live) UDP (User Datagram Protocol) Unicast UTP Cable Index Operation Optional board 57 Preparation for clock CE Conformity Information