Error Messages, 11-4, Error messages | Furuno FS-5070 specification

11. MAINTENANCE & TROUBLESHOOTING

11.4Error Messages

The table below shows error messages, their meanings, and remedies. If oter error occurs, contact your dealer.

Error messages

Error message	Meaning
Busy: RT	Radiotelephone is in operation.

Channel Busy	You attempted to transmit on a
	channel which is currently busy.
	(This occurs with Routine and
	Business priorities only.)
EPFS error	No position data from navigator for
	one minute.

Incoming	Incoming DSC call

No position data	The position data is interrupted
	while AUTO operation.
No response: RT	Radiotelephone is not powered or is
	disconnected.
Oven cold. Tx not	Oven too cold; cannot transmit.
ready; wait
Printer not ready	Automatic print is selected;
	however, printer is not powered or is
	disconnected.
Trouble: Oven not	Oven not ready; cannot transmit.
ready
TRX PLL UNLOCK	TRX PLL unlock. Transmission is
	stopped.
TUNE error	Tuning failed. Transmission power is
	decreased to LOW2. For NBDP,
	transmission is stopped.

Warning: Update	Position data is older by the amount
position	of time preset on the Alarm menu.

Watchdog error.	Internal error (such as CPU trouble)
Please Power OFF	detected. Accompanied with alarm,
	same type as for distress.
RX1 PLL UNLOCK	W/R1, W/R2 PLL unlock.
RX2 PLL UNLOCK	Transmission is stopped.
Ship’s mains failure	Power input has been switched from
	AC to DC at PR-850A.

Remedy

Wait until the radiotelephone is free.

The message is automatically erased when the channel becomes clear.

Press the CANCEL key to silence the alarm. Check the navigator. If it is malfunctioning, manually enter position.

Message is automatically cleared when DSC signal has gone. Check the navigator.

Check radiotelephone connection.

Wait until the oven becomes sufficiently warm.

Check printer.

Wait until the oven is ready.

Contact your dealer.

Try to tune again. If unsuccessful, confirm if TUNE error occurs on other frequencies. See “Antenna coupler cannot tune antenna” on page 11-3, or contact your dealer. Press the CANCEL key to silence alarm. Reenter position on the Position menu.

Turn the power off and on to erase the message. Have a qualified technician check the set.

Contact your dealer.

Press the CANCEL key to use the low output power. Check the AC input supply.

11-4

Image 172

Furuno FS-5070 manual Error Messages, 11-4, Error messages

Contents

Model FS-5070 00016050113 Important Notice How to discard this product How to discard a used batteryGeneral Safety Instructions Iii Distress Alert Message Procedure For IC-302 option operation Canceling Distress Alert Distress Cancellation Proc. Select frequency Push Enter Send cancel msg. by voice on 2182.0 kHz Communicate, via radiotelephone, with the coast station Table of Contents Viii Send calls Menu Operation Nbdp TRANSMITTING, Receiving 11.1 11-111.2 11-2 Features ForewordXii General Program Number Xiii System Configurations Standard configuration is shown with solid lineXiv FS-1570 FS-2570 Terminal Unit Xvi FS-5070 PWR/VOL knob Turns the power on/off Adjusts volume Operational OverviewControls Description of controls Radiotelephone RT Screen Turning the Power On/OffRadiotelephone RT screen Indication DSC Standby ScreenDSC standby screen Control Unit Dimmer, Contrast Setting Scan FrequenciesLoudspeaker Setting for Auto Acknowledgement System CharacteristicsEquipment priority Controls become inoperative Automatic setting of working frequency Intercom SSB Radiotelephone Choosing Class of Emission Choosing Channel, Frequency Choosing channelChoosing band and band channel with the Enter knob Rotate the Enter knob to set band or channel desired Transmitting procedure TransmittingChoosing frequency Entering frequency with the numeric keys Reducing transmitter power Condition of the transmitting unit RF gain sensitivity adjustment Checking the transmitting powerRotate the Enter to adjust and then push the Enter knob Receiving Receiving AM broadcasting stations Squelch functionNoise blanker Squelch on/off When Automatic Tuning Fails High Tension Hazard User Channels What is DSC? DSC OverviewDSC Message Call Description Contents of a DSC call Audio Alarms Alarm Frequency interval Receive calls Interpreting Call DisplaysDistress receive call Send calls Individual receive callReceived message View message Individual send call Compose msg Distress Operations Sending Distress AlertDistress operation overview Ship in Distress Distress Operations Received message Twice and then go to step Push the Enter knob to open the Input Type menuPush the Enter knob to open the latitude input window Push the Enter knob to open the time input window Compose msg Display changes as below example Communicating by Nbdp Terminal Unit Receiving a Distress Alert Distress alert received on MF band Action for ship receiving distress alert on MF band Distress alert message received Distress alert received on HF band Distress acknowledge message in progress Action for ships receiving distress alert on HF band Agree Sending the distress relay to coast station on HF band Push the Enter knob to open the DSC FREQ. Menu Wait for distress relay acknowledge Sending Distress Relay on Behalf of a Ship in Distress Sending distress relay to coast station Push the Enter knob to open the Ship ID in Dist window Ship ID in Dist Telephone Press the Cancel key to silence the audio alarm Priority distress Transmit sure?Distress relay coast message in progress Distress relay ack message received Sending distress relay to area ships Area Circle Ship ID in Dist Nature Telephone Distress relay area message in progress Cancelling Distress Call Receiving Distress Relay from Coast Station Distress Cancellation Proc. Select frequency Push Enter Routine Message CALLING, Receiving Individual CallSending an individual call Operation overview Push the Enter knob to open the Priority menu NBDP-ARQ Safety or urgency priority How to Set Working Frequency, ChannelRoutine priority How to Set DSC Frequency Compose msg Press Call key for forced transmission Able acknowledge message received Able acknowledge call received Unable acknowledge call received Receiving an individual call No response! Try calling again?Send Able acknowledge Send Unable acknowledge Manually Sending automatic acknowledge ACK BQ with comply type Able Sending automatic acknowledge ACK BQ with comply type Unable Unable acknowledge message in progress Manually acknowledging individual call with Able Manually acknowledging individual call with Unable No Reason Reason Busy Sending a group call Group CallPress the 2/DSC key Select Message MHZ Receiving a group call Sending message by Nbdp Terminal Unit Geographical Area Call Receiving message by Nbdp Terminal Unit Sending a geographical area call Area Receiving a geographical area call Geographical Area Sender ID Neutral Craft Call Sending a neutral craft call Receiving a neutral craft call Medical Transport Call Sending a medical transport call 2187.5 Receiving a medical transport call Receiving a Polling Request Press the Cancel key to return to the radiotelephone screenAutomatic reply Manual reply Position Call Requesting other ship’s positionFinding position of other station Sending own ship’s position to other station Station ID Cancel call Press the Cancel key Position call other ship requests your positionAcknowledge message received Automatic reply If canceling to send the reply, press the Cancel key Manual reply Pstn Call Sending a Pstn call, receiving acknowledge back ACK BQ Push the Enter knob to open the TEL NO. menu To scroll Waiting for acknowledgement Then, one of the following displays appears Receiving a Pstn call, sending acknowledge back ACK BQUnable acknowledge message received Shortly thereafter, one of the following messages appears No response! charge information Manual To return to the log selected, press the Cancel key To view the contents of a file, do the followingDeleting log files This page is intentionally left blank Setup Adjusting Handset VolumeMenu Operation Noise Blanker Squelch FrequencyRegistering user channels User ch entry Push the Enter knob to open the user channel options window User ch Preparing TX Message Deleting user channelsPreparing individual calls Deleting individual user channels Push the Enter knob to open the Station ID entry window Frequency How to Enter File Name and Number Push the Enter knob to open the file name entry window Preparing group calls Push the Enter knob to continue Message 2 MHZ Preparing Pstn calls Preparing test call Sending prepared messages Deleting send messageSending without modification Editing before sending Printing List of Send Message Files Manual Entry of Position and TimeDeleting all messages After last digit Date and Time Setting Date/Time setupMemory Clear Memory clear Clearing received distress log Clearing received ordinary logClearing transmitted log Restoring to default setting Setting AlarmsClearing user channels Sound Setting Sound setup Setting the Auto ACK Details OFF Hook Printing Messages Sample printouts Distress and safety frequencies Scan freq setup Routine frequencies Key Assignment Key assign setupSpecial Messages Speaker Setting in Off Hook FAX Enable/DisableOperation Timer Off This page is intentionally left blank Turning on the Nbdp System Nbdp System OverviewNbdp terminal unit, printer and keyboard Features of the IB-583 Description of EquipmentTerminal unit Communication status display Keyboard for IB-581 KeyboardKeyboard for IB-583 Function Keys, Menu Operation Menu conventionsInverse video Underline Menu overview Selecting menusFile menu Selecting menu items and options Function key description Function key F2 Edit menu UndoCut Copy Cancel Sending Timer OperationFunction key F3 Operate menu Call Station Or month, choose item with ↑ or ↓ key and change setting Function key F4 Window menuWindow menu Displays desired calendar month and year. To change year Timer Operation Entry Function key F5 Station menuStation Entry Scan Entry Setup Slave DelayFunction key F6 System menu TX/RX MSG Save Cursor is choosing Window Color Setup press the Enter key Function key F10 Break Disconnects the line Nbdp Preparations Registering Answerback Code & ID CodesRegistering answerback code Answerback code entry screen Registering ID codes Message for confirmation of code enteredIf the code is correct, press the Enter key again ID code entry screen Station List Registering stations Editing/Deleting stations OK/Cancel promptScanning group list Timer Programming Registering timer programsTimer operation entry screen 3 5 0 Editing/Deleting timer programs User channel entry screen Scan Channel Groups Editing/Deleting user channelsRegistering scan channel groups Scan entry screen Editing/Deleting scan channel groups Press the Enter key twice Press the ESC key Nbdp File Operations Opening and Closing FilesCreating Files How a file is opened Saving a File Formatting floppy disks Editing Files Saving a fileCutting and pasting text Close text screen Copying and pasting text Cutting textHighlight Pasting text Copy and paste flow diagram Select allSearching text Search screen Replacing text Goto lineGoto top, Goto bottom Replace screen Switching between files Opening FilesRenaming Files Opening a file Saving a File Under a New Name Deleting FilesReal Time Printing Printing Files Nbdp TRANSMITTING, Receiving Manual Calling10-1 Set frequency screen 10-2 Manual calling screen ARQ Mode Operation 10-3Establishing connection Press the 1 key to choose Call Station 10-4 Transmit message by one of the following methodsSending a file stored on a floppy disk Send file screen FEC Mode Operation Choosing Receive Mode10-5 Stopping transmission 10-6 Communication ExampleCommunications example 10-7 Table of abbreviations Timer Operation Enabling timer operationCommand and abbreviation Timer operation list Scanning Stopping timer operation10-9 Communication Buffer Preparing Macrofiles for Automatic TelexAutomatic telex overview 10-10 Preparations 10-11Registering answerback code Registering scan groups Commands Command Parameter ContentCommands processed by Danish coast station Lyngby Command Function Store-and-forward method Actual procedure for store-and-forward telex10-13 Sample macrofile for store-and-forward method 10-14Close text prompt Dirtlx macrofile 10-15Sample Dirtlx macrofile Sample Dirltx macrofile Procedure for Dirtlx 10-16 Automatic Telex using Macrofile Basic procedureActual procedure 10-17 Call macro screen 10-18Press the ↓ key to choose a macrofile Press the Enter key Radiotelephone Test Maintenance & Troubleshooting11-1 Maintenance 11-2 Simple Troubleshooting 11-3 Error messages Error Messages11-4 Replacement of Fuses 11-5 Test Call 11-6 Do the either way depending on the message shown in step 11-7Test acknowledge message received Nbdp Terminal Unit Maintenance 11-9 System menu Example IB-583Self test results Tone test Tone test 2 Fox 11-10Tone test 3 Beta Menu Tree AppendixAP-1 Nbdp terminal unit telex AP-2 Frequency Tables AP-3TX kHz RX kHz Remarks File Name 14. = Ship-to-ship Custom channels to be programmed by Furuno dealers AP-4 MF band working carrier frequencies ref. US CFR 47 Part AP-5 MF band SSB working carrier frequencies AP-6 MHz ITU SSB carrier frequencies ITU RR Appendix AP-7 AP-8 12/16 ITU SSB carrier frequencies ITU RR Appendix AP-9 18/19, 22, 25/26 ITU SSB carrier frequencies ITU RR Appendix AP-10 MF band telex frequency table AP-11 AP-12 Frequency /4 AP-13 ITU Telex frequency /4 AP-14 ITU Telex Frequency /4 Telex Abbreviations AP-16 Digital Interface IEC SentencesAP-17 Input sentences IEC GLL Geographic position latitude/longitude AP-18ZDA Time and date AP-19 GNS Gnss fix data AP-20 RMC Recommended minimum specific GPS/TRANSIT data Schematic diagram AP-21 AP-22 Parts ListTransceiver unit FS-1570T AP-23 Transceiver unit FS-2570T AP-24 Control unit FS-2571C AP-25 Control unit FS-5070T FS-1570T Parts LocationAP-26 Transceiver unit FS-2570T AP-27 Transceiver unit FS-5070T AP-28 AP-29 Comb Control unit FS-2571C AP-30 Specifications of SSB Radiotelephone FS-1570/2570/5070 DSC/WATCH Keeping Receiver DSC/WATCH Receiver FS-5070 Nbdp Function Option Terminal Unit IB-581 FS-1570/2570 Antenna Coupler FS-1570/2570 Antenna Coupler FS-5070 Coating Color Index Distress relay IN-2 0560 Publication No. DOC-1028 0560