Turning the Power On/Off, Radiotelephone RT Screen | Furuno FS-5070

1. OPERATIONAL OVERVIEW

7/					key	Turns loudspeaker on/off.


						(Note that this key does not silence the distress or urgency alarm.)

8/PRINT key						Prints communications log files, current screen (except DSC standby
						screen and radiotelephone screen) and test results.
9/					key	Adjusts panel dimmer and LCD contrast.



*/FILE/CURSOR						•	Opens the send message file list from the DSC standby screen, to send
key							stored message.
						•	Shifts cursor.
0/LOG/TUNE key						•	Long press: Tunes antenna in radiotelephone operation.
						•	Momentary press: Displays message logs.
#/SETUP key						Opens the main menu.
ALARM lamp						•	Flashes in red for distress and urgency messages.
						•	Flashes in green for safety and routine messages.
OVEN lamp						Lights (in green) when mains switchboard is on.

1.2Turning the Power On/Off

Turn the PWR/VOL knob clockwise at the right-hand side of the control unit to power the system. The RT screen appears.

Rotate the PWR/VOL knob counterclockwise to turn the system off.

In the dual control unit system, the control unit connected to the CONTROLLER 1 port on the transceiver unit has priority and it controls the power for both the No.1 and No. 2 control units. The power switch of the No. 2 control unit powers on/off the No. 2 control unit only.

Note: Turn on power at switchboard more than five minutes before turning on this equipment.

1.3Radiotelephone (RT) Screen

Turn the power on, or press the 1/ RT/CH key to show the radiotelephone screen. This is where you set up the transceiver unit, and communicate by voice or telex.

CH: 200 DR

Tx: 2182.0 kHz

Rx: 2182.00 kHz

SSB SIMP HIGH FAST NB SQ

SEN					S
SEN					S
IA					10.0A
IA					10.0A

MMSI xxxxxxxxx							UTC 00:00
POS 35 00.0000N							UTC 00:00
135 00.0000E							EPFS 23:59

Radiotelephone (RT) screen

1-2

Image 20

Furuno FS-5070 manual Turning the Power On/Off, Radiotelephone RT Screen, Radiotelephone RT screen

Contents

Model FS-5070 00016050113 General How to discard this product How to discard a used batteryImportant Notice Safety Instructions Iii Distress Alert Message Procedure For IC-302 option operation Canceling Distress Alert Distress Cancellation Proc. Select frequency Push Enter Send cancel msg. by voice on 2182.0 kHz Communicate, via radiotelephone, with the coast station Table of Contents Viii Send calls Menu Operation Nbdp TRANSMITTING, Receiving 11.1 11-111.2 11-2 Features ForewordXii General Program Number Xiii System Configurations Standard configuration is shown with solid lineXiv FS-1570 FS-2570 Terminal Unit Xvi FS-5070 PWR/VOL knob Turns the power on/off Adjusts volume Operational OverviewControls Description of controls Radiotelephone RT screen Turning the Power On/OffRadiotelephone RT Screen DSC standby screen DSC Standby ScreenIndication Loudspeaker Setting Scan FrequenciesControl Unit Dimmer, Contrast Setting for Auto Acknowledgement System CharacteristicsEquipment priority Controls become inoperative Automatic setting of working frequency Intercom SSB Radiotelephone Choosing Class of Emission Choosing Channel, Frequency Choosing channelChoosing band and band channel with the Enter knob Rotate the Enter knob to set band or channel desired Transmitting procedure TransmittingChoosing frequency Entering frequency with the numeric keys Reducing transmitter power Condition of the transmitting unit RF gain sensitivity adjustment Checking the transmitting powerRotate the Enter to adjust and then push the Enter knob Receiving Receiving AM broadcasting stations Squelch functionNoise blanker Squelch on/off When Automatic Tuning Fails High Tension Hazard User Channels What is DSC? DSC OverviewDSC Message Call Description Contents of a DSC call Audio Alarms Alarm Frequency interval Distress receive call Interpreting Call DisplaysReceive calls Send calls Individual receive callReceived message View message Individual send call Compose msg Distress Operations Sending Distress AlertDistress operation overview Ship in Distress Distress Operations Received message Push the Enter knob to open the latitude input window Push the Enter knob to open the Input Type menuTwice and then go to step Push the Enter knob to open the time input window Compose msg Display changes as below example Communicating by Nbdp Terminal Unit Receiving a Distress Alert Distress alert received on MF band Action for ship receiving distress alert on MF band Distress alert message received Distress alert received on HF band Distress acknowledge message in progress Action for ships receiving distress alert on HF band Agree Sending the distress relay to coast station on HF band Push the Enter knob to open the DSC FREQ. Menu Wait for distress relay acknowledge Sending Distress Relay on Behalf of a Ship in Distress Sending distress relay to coast station Push the Enter knob to open the Ship ID in Dist window Ship ID in Dist Telephone Press the Cancel key to silence the audio alarm Priority distress Transmit sure?Distress relay coast message in progress Distress relay ack message received Sending distress relay to area ships Area Circle Ship ID in Dist Nature Telephone Distress relay area message in progress Cancelling Distress Call Receiving Distress Relay from Coast Station Distress Cancellation Proc. Select frequency Push Enter Routine Message CALLING, Receiving Individual CallSending an individual call Operation overview Push the Enter knob to open the Priority menu NBDP-ARQ Routine priority How to Set Working Frequency, ChannelSafety or urgency priority How to Set DSC Frequency Compose msg Press Call key for forced transmission Able acknowledge message received Able acknowledge call received Unable acknowledge call received Receiving an individual call No response! Try calling again?Send Able acknowledge Send Unable acknowledge Manually Sending automatic acknowledge ACK BQ with comply type Able Sending automatic acknowledge ACK BQ with comply type Unable Unable acknowledge message in progress Manually acknowledging individual call with Able Manually acknowledging individual call with Unable No Reason Reason Busy Press the 2/DSC key Select Message Group CallSending a group call MHZ Receiving a group call Sending message by Nbdp Terminal Unit Geographical Area Call Receiving message by Nbdp Terminal Unit Sending a geographical area call Area Receiving a geographical area call Geographical Area Sender ID Neutral Craft Call Sending a neutral craft call Receiving a neutral craft call Medical Transport Call Sending a medical transport call 2187.5 Receiving a medical transport call Automatic reply Press the Cancel key to return to the radiotelephone screenReceiving a Polling Request Manual reply Position Call Requesting other ship’s positionFinding position of other station Sending own ship’s position to other station Station ID Cancel call Press the Cancel key Position call other ship requests your positionAcknowledge message received Automatic reply If canceling to send the reply, press the Cancel key Manual reply Pstn Call Sending a Pstn call, receiving acknowledge back ACK BQ Push the Enter knob to open the TEL NO. menu To scroll Waiting for acknowledgement Unable acknowledge message received Receiving a Pstn call, sending acknowledge back ACK BQThen, one of the following displays appears Shortly thereafter, one of the following messages appears No response! charge information Manual Deleting log files To view the contents of a file, do the followingTo return to the log selected, press the Cancel key This page is intentionally left blank Menu Operation Adjusting Handset VolumeSetup Noise Blanker Squelch FrequencyRegistering user channels User ch entry Push the Enter knob to open the user channel options window User ch Preparing TX Message Deleting user channelsPreparing individual calls Deleting individual user channels Push the Enter knob to open the Station ID entry window Frequency How to Enter File Name and Number Push the Enter knob to open the file name entry window Preparing group calls Push the Enter knob to continue Message 2 MHZ Preparing Pstn calls Preparing test call Sending prepared messages Deleting send messageSending without modification Editing before sending Deleting all messages Manual Entry of Position and TimePrinting List of Send Message Files After last digit Date and Time Setting Date/Time setupMemory Clear Memory clear Clearing transmitted log Clearing received ordinary logClearing received distress log Clearing user channels Setting AlarmsRestoring to default setting Sound Setting Sound setup Setting the Auto ACK Details OFF Hook Printing Messages Sample printouts Distress and safety frequencies Scan freq setup Routine frequencies Special Messages Key assign setupKey Assignment Operation Timer Off FAX Enable/DisableSpeaker Setting in Off Hook This page is intentionally left blank Nbdp terminal unit, printer and keyboard Nbdp System OverviewTurning on the Nbdp System Features of the IB-583 Description of EquipmentTerminal unit Communication status display Keyboard for IB-583 KeyboardKeyboard for IB-581 Function Keys, Menu Operation Menu conventionsInverse video Underline Menu overview Selecting menusFile menu Selecting menu items and options Function key description Function key F2 Edit menu UndoCut Copy Cancel Sending Timer OperationFunction key F3 Operate menu Call Station Or month, choose item with ↑ or ↓ key and change setting Function key F4 Window menuWindow menu Displays desired calendar month and year. To change year Timer Operation Entry Function key F5 Station menuStation Entry Scan Entry Setup Slave DelayFunction key F6 System menu TX/RX MSG Save Cursor is choosing Window Color Setup press the Enter key Function key F10 Break Disconnects the line Nbdp Preparations Registering Answerback Code & ID CodesRegistering answerback code Answerback code entry screen Registering ID codes Message for confirmation of code enteredIf the code is correct, press the Enter key again ID code entry screen Station List Registering stations Scanning group list OK/Cancel promptEditing/Deleting stations Timer Programming Registering timer programsTimer operation entry screen 3 5 0 Editing/Deleting timer programs User channel entry screen Scan Channel Groups Editing/Deleting user channelsRegistering scan channel groups Scan entry screen Editing/Deleting scan channel groups Press the Enter key twice Press the ESC key Nbdp File Operations Opening and Closing FilesCreating Files How a file is opened Saving a File Formatting floppy disks Editing Files Saving a fileCutting and pasting text Close text screen Copying and pasting text Cutting textHighlight Pasting text Copy and paste flow diagram Select allSearching text Search screen Replacing text Goto lineGoto top, Goto bottom Replace screen Switching between files Opening FilesRenaming Files Opening a file Saving a File Under a New Name Deleting FilesReal Time Printing Printing Files Nbdp TRANSMITTING, Receiving Manual Calling10-1 Set frequency screen 10-2 Manual calling screen ARQ Mode Operation 10-3Establishing connection Press the 1 key to choose Call Station 10-4 Transmit message by one of the following methodsSending a file stored on a floppy disk Send file screen FEC Mode Operation Choosing Receive Mode10-5 Stopping transmission Communications example Communication Example10-6 10-7 Table of abbreviations Timer Operation Enabling timer operationCommand and abbreviation Timer operation list 10-9 Stopping timer operationScanning Communication Buffer Preparing Macrofiles for Automatic TelexAutomatic telex overview 10-10 Preparations 10-11Registering answerback code Registering scan groups Commands Command Parameter ContentCommands processed by Danish coast station Lyngby Command Function 10-13 Actual procedure for store-and-forward telexStore-and-forward method Close text prompt 10-14Sample macrofile for store-and-forward method Dirtlx macrofile 10-15Sample Dirtlx macrofile Sample Dirltx macrofile Procedure for Dirtlx 10-16 Automatic Telex using Macrofile Basic procedureActual procedure 10-17 Press the ↓ key to choose a macrofile Press the Enter key 10-18Call macro screen 11-1 Maintenance & TroubleshootingRadiotelephone Test Maintenance 11-2 Simple Troubleshooting 11-3 11-4 Error MessagesError messages Replacement of Fuses 11-5 Test Call 11-6 Test acknowledge message received 11-7Do the either way depending on the message shown in step Nbdp Terminal Unit Maintenance 11-9 System menu Example IB-583Self test results Tone test Tone test 3 Beta 11-10Tone test 2 Fox AP-1 AppendixMenu Tree Nbdp terminal unit telex AP-2 Frequency Tables AP-3TX kHz RX kHz Remarks File Name 14. = Ship-to-ship Custom channels to be programmed by Furuno dealers AP-4 MF band working carrier frequencies ref. US CFR 47 Part AP-5 MF band SSB working carrier frequencies AP-6 MHz ITU SSB carrier frequencies ITU RR Appendix AP-7 AP-8 12/16 ITU SSB carrier frequencies ITU RR Appendix AP-9 18/19, 22, 25/26 ITU SSB carrier frequencies ITU RR Appendix AP-10 MF band telex frequency table AP-11 AP-12 Frequency /4 AP-13 ITU Telex frequency /4 AP-14 ITU Telex Frequency /4 Telex Abbreviations AP-16 Digital Interface IEC SentencesAP-17 Input sentences IEC ZDA Time and date AP-18GLL Geographic position latitude/longitude AP-19 GNS Gnss fix data AP-20 RMC Recommended minimum specific GPS/TRANSIT data Schematic diagram AP-21 Transceiver unit FS-1570T Parts ListAP-22 AP-23 Transceiver unit FS-2570T AP-24 Control unit FS-2571C AP-25 Control unit FS-5070T AP-26 Parts LocationFS-1570T Transceiver unit FS-2570T AP-27 Transceiver unit FS-5070T AP-28 AP-29 Comb Control unit FS-2571C AP-30 Specifications of SSB Radiotelephone FS-1570/2570/5070 DSC/WATCH Keeping Receiver DSC/WATCH Receiver FS-5070 Nbdp Function Option Terminal Unit IB-581 FS-1570/2570 Antenna Coupler FS-1570/2570 Antenna Coupler FS-5070 Coating Color Index Distress relay IN-2 0560 Publication No. DOC-1028 0560