Installation
ATTENTION INSTALLER:FOR A QUALITY INSTALLATION, FOLLOW THESE INSTRUCTIONS.
ROLLERS
• REMOVE AND DISCARD |
SKIDBOARDS and bolts used to |
hold skidboards. |
CARDBOARD
PROTECTS
DOOR EDGES
MAKE SURE FRONT
ROLLERS DO NOT
REST ON TRUCK
RAISE
DO NOT
OVER-
TIGHTEN
STRAP
ROLLER
ADJUSTMENT
TRUCK FROM
SIDE ONLY
•ADJUST FRONT ROLLERS
so that refrigerator is solid and doors close easily.
9 IS COLDEST
0 IS OFF
4 | 5 | 6 | 4 | 5 | 6 |
3 |
| 7 | 3 |
| 7 |
2 |
| 8 | 2 |
| 8 |
|
|
|
| ||
1 |
| 9 | 1 |
| 9 |
0 |
|
|
|
|
|
FREEZER | FRESH FOOD |
•SET BOTH CONTROLS TO “5”.
•SET ICEMAKER TO OFF until
water line is connected.
• Use PADDED HAND TRUCK |
to protect refrigerator finish. |
• LEAVE TAPE ON DOORS until | • MAKE SURE DOORS ARE EVEN |
refrigerator is in its final location. | AT TOP. Check gasket seal. |
•IMPORTANT: IMMEDIATELY REMOVE ALL CLEAR PROTECTIVE TAPE FROM TRIM.
•TO REMOVE TAPE RESIDUE AND HANDPRINTS, USE APPLIANCE POLISH.
•REMOVE ALL TAPE AND OTHER PACKAGING MATERIAL FROM INSIDE REFRIGERATOR. DO NOT REMOVE SERIAL PLATE.
IF NECESSARY TO REMOVE DOORS, REMOVE ALL HINGES. FOR DISPENSER MODELS:
TO REINSTALL DOORS...
TUBING CLIP
COLLAR
PRESS THE WHITE COLLAR AS YOU PULL OUT THE TUBING.
WHEN INSTALLING DOORS... |
5⁄8″ – 3⁄4″ |
• Push tubing into connector |
(5⁄8″ to 3⁄4″ ) to prevent leakage. |
HINGE COVER
WIRING CONNECTORS
ALIGN DOORS EVENLY | FRESH FOOD HINGE |
AT TOP | ADJUSTMENT PIN |
• | Reinstall lower hinges and tighten hinge screws firmly. |
• Place door on lower hinge pin and install upper hinges. | |
| Tighten upper hinge screws firmly. |
• | Align both doors evenly at top by adjusting pin on lower |
| fresh food hinge. |
• | At lower left hinge, remove tubing | • | At upper hinges, disconnect wiring connectors. |
| from the clip. | • | Remove both hinges with each door to prevent |
|
| ||
• | Disconnect the water line. |
| damage to tubing or wiring. |
• Reconnect wiring connectors and reinstall hinge covers. | |
• | Reinstall tubing by pushing tubing into connector. |
• | Put tubing back into clip. |
FRANÇAIS • ESPANOL
PREFERRED
METHOD
MAKE SURE PROPER
GROUND EXISTS
BEFORE USE
TEMPORARY METHOD (Adapter plugs not permitted in Canada)
ENSURE PROPER
GROUND AND
FIRM CONNECTION
BEFORE USE
IMPORTANT: PLEASE READ CAREFULLY
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
The power cord of this appliance is equipped with a
Where a standard
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
USAGE SITUATIONS WHERE THE APPLIANCE’S POWER CORD WILL BE DISCONNECTED INFREQUENTLY
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug. However, if you still elect to use an adapter, where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded
CAUTION: Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall receptacle is grounded through the house wiring. The customer should have the circuit checked by a qualified electrician to make sure the receptacle is properly grounded. When disconnecting the power cord from the adapter, always hold the adapter with one hand. If this is not done, the adapter ground terminal is very likely to break with repeated use. Should this happen, DO NOT USE the appliance until a proper ground has again been established.
USAGE SITUATIONS WHERE THE APPLIANCE’S POWER CORD WILL BE DISCONNECTED FREQUENTLY
Do not use an adapter plug in these situations because frequent disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the adapter ground terminal. The customer should have the
197D3266P001 31-5087 9-00 JR
– 3 –