|
| Maintenance | |
~ | • | Turn ON the utility power supply to the transfer switch, using | |
A The Maintenance Disconnect Switch and |
| the means provided (such as the utility power source main line | |
| circuit breaker) . | ||
.... the AUTO/OFF/MANUAL switches (if so | • | Let the generator run at | |
equipped) must be set properly, or the |
| internal temperatures. | |
generator will crank and start as soon as | • | Shut down the generator. | |
the UTILITY power to the transfer switch is | |||
|
| ||
turned off. Refer to applicable control panel | OPERATING UNIT WITH AUTOMATIC | ||
and transfer switch manuals for more infor- | |||
mation. | TRANSFER SWITCH | ||
A Do not proceed until certain that utility | If the generator has been installed along with an automatic transfer | ||
.... source voltage is available to the transfer | switch, such as a | ||
switch and the transfer switch main contacts | stopped automatically or manually. | ||
are set to UTILITY. |
| NOTE: | |
|
| ||
/r\ Do not attempt manual operation until all | Refer to the applicable manual for the transfer switch and to | |
illpower supplies to the transfer switch have | ||
"Transfer Switch Start Signal Connections". In addition, please | ||
been positively turned off, or extremely dan- | ||
note the dangers under "Engine | ||
gerous - possibly lethal - electrical shock | ||
| ||
will result. |
| |
|
/i). Transfer switch enclosure doors should be ~kept closed and locked. Only authorized
personnel should be allowed access to the transfer switch Interior. Extremely high and dangerous voltages are present in the trans- fer switch.
In order to manually transfer load from the utility source to the generator, follow these directions:
•Turn OFF or disconnect the utility power circuit to the transfer switch, using the means provided (such as the utility source main line circuit breaker).
•Set the transfer handle to its UTILITY (NORMAL) position with load circuits connected to the utility power supply.
•Set the stationary emergency generator'smain line circuit breaker to its OFF (or OPEN) position.
•Start the generator.
•Let engine stabilize and warm up.
•Check all applicable instrument and gauge readings. When certain that all readings are correct, move the transfer switch manual handle to its STANDBY (GENERATOR) position, i.e, load circuits supplied by the generator.
•Set the stationary emergency generator'smain line circuit breaker to its ON (or CLOSED) position.
•Load circuits are now powered by the stationary emergency generator.
RETRANSFER AND SHUTDOWN
For additional information, refer to the applicable control panel manual for this unit, as well as any literature pertaining to the transfer switch.
To manually transfer the load back to the utility power source and shut down the generator, follow these directions:
•Set the stationary emergency generator'smain line circuit breaker to its OFF (or OPEN) position.
•Manually move the transfer switch handle to its UTILITY (NOR- MAL) position, i.e., load cirCUits connected to the utility.
SERVICE SCHEDULE
AUTHORIZED OPERATOR MAINTENANCE FUNCTIONS
Every Month or 100 Hours (whichever comes first)
•Test stationary emergency generator system.
•Inspect battery (batteries) and cables.
•Check engine oil level.
•Check gearbox oil level (if so equipped).
•Check engine coolant level.
•Check generator ground connections.
•Test/inspect starting aids.
Every Three Months or Every 120 Hours (whichever comes first)
•Inspect and test fuel system and connections.
•Inspect exhaust system.
•Inspect/test fuel supply system.
AUTHORIZED SERVICE TECHNICIAN MAINTENANCE FUNCTIONS
After First 30 Hours of Operation
•Inspect Wiring.
•Change engine crankcase oil and oil filter.
•Inspect engine fan belts.
•Inspect battery (batteries) and cables.
Every Six Months or Every 200 Hours (whichever comes first)
•Lubricate engine controls.
•Service engine air cleaner.
•Service engine fuel filter.
•Inspect AC generator.
•Test engine safety controls.
•Inspect fan belts.
•Check engine coolant level.
•Inspect engine cooling system hoses.
17
