Gigabyte AGP 4X(1.5V) manual Troubleshooting

Models: AGP 4X(1.5V)

1 112
Download 112 pages 42.51 Kb
Page 107
Image 107

Troubleshooting

If you encounter any trouble during boot up, please follow the troubleshooting procedures .

START

Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard.

Please make sure motherboard & chassis are not short

 

 

Yes

Please isolate

?

 

 

 

 

 

 

 

 

 

 

 

the short pin.

No

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Failure has been excluded.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Please make sure all jumper settings (such as CPU system bus

 

 

No

Make sure the

 

 

jumper setting

 

 

 

 

speed, frequency ratio, voltage and etc.) are set properly.

 

 

 

 

are correct.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yes

 

 

 

 

 

 

 

 

 

 

 

 

Failure has been excluded.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Plug the CPU

 

 

 

 

 

 

 

 

 

 

No

cooling fan power

Check if the CPU cooling fan attached to CPU properly. ls

 

 

in the CPU fan

 

 

 

 

connector. Plug in

CPU cooling fan power connected to CPU_FAN

 

 

 

 

the AC power

properly?

 

 

 

 

connector.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Failure has been excluded.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No

Insert and push

Check if the memory install properly into the DIMM slot.

 

 

 

 

the memory

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

module vertically

Yes

 

 

 

 

 

 

 

 

 

 

 

into the DIMM slot.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Failure has been excluded.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Insert the VGA card. Then plug in ATX power cable and turn on the system.

A

English

-103-

Appendix

Page 107
Image 107
Gigabyte AGP 4X(1.5V) manual Troubleshooting