Manuals / Graco / Power Tools / Paint Sprayer

Graco 16H242, 262612 Setup, Flexible Suction Tube, Spraying Ceilings, Walls and Crown Molding

Models: 16H829 16H242 262612

1 32

Download 32 pages 47.92 Kb

Page 11

Setup

Setup

Setup

Flammable fumes (such as solvent and paint fumes) in work area can ignite or explode.

See Grounding Instructions, page 3.

Do not spray flammable or combustible liquids in a con- fined area.

Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area.

NOTICE

Your sprayer is NOT compatible with harsh cleaners such as chlorine bleach. Using these cleaners will cause damage to the sprayer.

NOTICE

Do NOT shake materials to be used with this sprayer. Some fine finish lacquers and enamels trap air when shaken, which can affect sprayer performance. Stir the material or check the manufacturer’s recommendation for the material being sprayed.

Flexible Suction Tube

This sprayer comes with a suction tube that can be adjusted for multi-directional spraying.

Spraying Ceilings, Walls and Crown Molding

When spraying ceilings or walls, rotate the suction tube collar to the front of the material cup.

ti16710a

Spraying Floors and Base Boards

When spraying floors, rotate the suction tube collar to the back of the material cup.

ti16709a

NOTE: If the sprayer is angled or tilted too far, the suc- tion tube will lose contact with the material and the sprayer will stop spraying.

ti16711a

3A1698F

11

Image 11

Graco 16H242 Setup, Flexible Suction Tube, Spraying Ceilings, Walls and Crown Molding, Spraying Floors and Base Boards

Contents

Operation Service only at Graco approved service centersFine Finish Hand-Held Paint Sprayer 3A1698FDO NOT RETURN THIS SPRAYER TO THE STORE Table of ContentsImportant User Information Grounding Wire Repair WarningsSKIN INJECTION HAZARD FIRE AND EXPLOSION HAZARDCHARGER ELECTRIC SHOCK, FIRE AND EXPLOSION HAZARD BATTERY HAZARDEQUIPMENT MISUSE HAZARD PERSONAL PROTECTIVE EQUIPMENT PRESSURIZED ALUMINUM PARTS HAZARDTOXIC FLUID OR FUMES HAZARD Component Identification Sprayer Status Indicator Charging the BatteryCharger Status Indicator Lights Spray Tip Position Pressure Relief ProcedureTrigger Lock Prime/Pressure Relief Valve PositionLow Speed Setting Hi/Lo SwitchAdjusting Pressure Motor SpeedSpraying Floors and Base Boards SetupFlexible Suction Tube Spraying Ceilings, Walls and Crown MoldingSprayer Setup Fine Finish Materials and Tip Sizes Reversible Tip Selection ChartStarting a New Job or Refilling the Cup Aiming Sprayer Install Tip/Guard Assembly if not installedGetting Started with Basic Techniques Triggering SprayerUnclogging Spray Tip/Guard Assembly Protect the internal parts of this sprayer from water Shutdown and CleaningFlushing Sprayer 10. If sprayer is not completely clean, repeat steps Fine Finish Tip Wear Cleaning Sprayer ExteriorStorage ti20355a Replacement Parts and KitsReplacement Parts and Kits 3A1698FParts List DescriptionNumber Order PartNumber Replacement Parts and KitsDescription If you have this model sprayerIf you have this model sprayer DescriptionNumber Order PartAlternate Priming Method Installation Inlet Valve Removal/ServiceInstallation Outlet Valve RepairRemoval Cause TroubleshootingProblem SolutionProblem Spray Pattern DiagnosticsProblem SolutionReplace tip. See Install Tip/Guard Assembly ProblemSolution See Reversible Tip Selection Chart, pageCharger Technical DataBattery SprayerMotor Speed Preferred Material Settings LogPreferred Material Settings Log Material3A1698F Original Graco Standard WarrantyGraco Information