Programming the Remote
4.The next display screen (Figure 47) is where you select the macro to be read. Press the
⁄¤ Navigation Buttons Euntil the name of the macro you wish to read appears. For this example, we will read back the Power On macro created in the previous section. When the name of the macro to be erased appears, press the Set Button F.
R E A D A M A C R O
P O W E R O N
Figure 47
5.As soon as the Set button is pressed, the first two steps in the macro will be appear in the remote’s LCD screen. You may then use the
⁄¤ Navigation Buttons Eto step up or down through the list of commands stored as the macro. As you read the display, you will see Device Selector Buttons 45 appear in brackets, (e.g., [AVR]). When the step in the macro is a function, navigation or any other button, it will appear next to the bracketed
6.When you are finished reviewing the macro’s contents, press the Set Button Fto return the remote to normal operation.
Punch-Through Configuration
Volume Punch-Through
Follow these steps to enable the Volume Up/Down and Mute controls from one device to be used when the remote is otherwise pro- grammed for a different device.
Note for Volume Punch-Through:
The remote’s default settings are for the AVR’s volume controls to be used when any input or device is selected with the exception of the VID 2/TV button. There is no need to program the remote for volume
1. Press and hold the Program Button for about three seconds while the message shown in Figure 15 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button F appears.
2.The remote’s MAIN MENU message (Figure 16), will appear in the LCD display and the
Set Button Fwill remain illuminated in
red. Press the ⁄¤ Navigation Buttons
Euntil
M A I N M E N U
P U N C H - T H R O U G H
Figure 48
3.At the next menu screen (Figure 49) press the Set Button Fto begin programming the remote for Volume
P U N C H - T H R O U G H
V O L U M E
Figure 49
4.The next display screen (Figure 50) is where you select the device that will receive the
D E V I C E I N U S E
T V
Figure 50
5.At the next display screen (Figure 51), you will select the device whose Volume Up/Down and Mute commands will be used. Press the ⁄¤
Navigation Buttons Euntil the desired device’s name appears to the right of the device in use. In our example, that is the AVR (indicated by AVR). When the desired combination of devices appears, press the Set Button F.
P U N C H - T H R O U G H
T V < - A V R
Figure 51
6.When the Set button is pressed, the display will change to show you that the new combi- nation of control commands is being saved to the unit’s memory, as shown in Figure 52. The word SAVED will flash four times and then the remote will return to normal operation.
T V < - A V R [ V O L ]
S A V E D
Figure 52
7.Once the
buttons | are pressed while the master |
device is in use. |
|
Returning the Volume Control Settings to Default Operation:
If you wish to remove the Volume
steps shown above, except that in Steps 4 and 5, select the same device for both the DEVICE IN USE on the left side of the bottom line and the
P U N C H - T H R O U G H
T V < - T V
Figure 53
Channel Punch-Through
Channel
Channel Up/Down Selectors to transmit commands to the cable box even though the other button commands are programmed to operate the VCR.
To program the AVR for Channel
1. Press and hold the Program Button for about three seconds while the message shown in Figure 15 appears in the remote’s LCD Information Display 2. Release the but- ton when the red light under the Set Button
Fappears.
2.The remote’s MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button Fwill remain illuminated in red. Press the ⁄¤ Navigation Buttons Euntil
3.At the next menu screen, press the ⁄¤
Navigation Buttons Euntil CHANNEL appears on the bottom line of the LCD screen, as shown in Figure 54. Press the Set Button
Fto begin programming the remote for Channel
P U N C H - T H R O U G H
C H A N N E L
Figure 54
4.The next display screen (Figure 55) is where you select the device that will receive the
PROGRAMMING THE REMOTE 51