Manuals / Brands / Computer Equipment / Switch / HP / Computer Equipment / Switch

HP ProCurve 2610 Switch the Installing, Figure 2-5.Mounting in a rack

1 112

Download 112 pages, 2.52 Mb

Installing the Switch

Installation Procedures

2.Hold the switch with attached brackets up to the rack and move it vertically until rack holes line up with the bracket holes, then insert and tighten the four number 12-24 screws holding the brackets to the rack.

Install 12-24

screws

Figure 2-5. Mounting in a rack

Switch the Installing

2-11

Contents

ProCurve 2610 Switches Page HP ProCurve 2610 Switches Installation and Getting Started Guide Safety Contents 1 Introducing the Switch 2 Installing the Switch 3 Configuring the Switch 4 Troubleshooting A Switch Specifications B Cabling and Technology Information C Safety and EMC Regulatory Statements D Recycle Statements Index Page Introducing the Switch following speeds and technologies: www.hp.com/go/procurve/manuals Front of the Switch Network Ports LEDs the Page Port LEDs Port LEDs LED Mode Select Button and Indicator LEDs the Introducing Figure 1-1.2610 non-PWRSwitches Figure 1-2. 2610-PWRSwitches Reset Button Clear Button Console Port Back of the Switch RPS and EPS Input Port Power Connector Switch Features console interface web browser Page Installing the Switch Included Parts J a p a n P o w e r C o r d W a r n i n g Installation Precautions Installation Procedures Prepare the installation site Verify the switch passes self test Mount the switch Connect power to the switch Page 1. Prepare the Installation Site 2. Verify the Switch Passes Self Test N o t e Figure 2-2.Checking the LEDs on the 2610 non-PWRswitches Figure 2-3.Checking the LEDs on the 2610-PWRswitches LED Behavior During the self test: When the self test completes successfully: Power Fan 3. Mount the Switch Rack Mounting the 2610-PWRswitches Figure 2-4.Attaching large mounting brackets Figure 2-5.Mounting in a rack Rack Mounting the Non-PWRSwitches Figure 2-6.Attaching small mounting brackets accessory kit to attach the mounting brackets to the switch Figure 2-7.Mounting in a rack Flat Wall Mounting C a u t i o n Supported Wall Mounting Positions The Switch 2610-PWRSwitches are not wall mountable Wall mounting Horizontal Horizontal Surface Mounting 4. Connect the Switch to a Power Source 5. Connect the Network Cables 6. Installing or Removing mini-GBICs 7. (Optional) Connect a Redundant Power Supply to a Switch 2610-PWRSeries The 600 RPS/EPS provides two types of power to the switches: The 610 EPS only provides external PoE power: RPS/EPS Operation Operating Characteristics of the 600 RPS/EPS (J8168A) Operating Characteristics of the 610 EPS (J8169A) 600 RPS/EPS LEDs Figure 2-12.RPS/EPS status LEDs Figure 2-13.Connecting a 600 RPS/EPS to a 2610 RPS 600 RPS/EPS 2610-PWRswitches Figure 2-14.Connecting a 600 RPS/EPS to multiple 2610s RPS Figure 2-15.Connecting a 600 RPS/EPS to a 2610 EPS 610 EPS LEDs Figure 2-16.EPS status LEDs Figure 2-17.Connecting a 610 EPS to two 2610s EPS Figure 2-18.Connecting a 610 EPS to four 2610s EPS 8. (Optional) Connect a Console to the Switch Direct Console Access Figure 2-19.Connecting the console cable ProCurve Switch # Sample Network Topologies for Non-PWRSwitches As a Desktop Switch As a Segment Switch Connecting to a Backbone Switch Page Sample Network Topologies for PWR Switches As a Desktop Switch Implementing PoE As a Segment Switch Implementing PoE Connecting to a Backbone Switch Implementing PoE Stacking the Switch Page Configuring the Switch Recommended Minimal Configuration Using the Console Setup Screen Where to Go From Here Page Using the IP Address for Remote Switch Management Starting a Telnet Session Starting a Web Browser Session Figure 3-2.Example web browser session Troubleshooting Basic Troubleshooting Tips Faulty or loose cables Non-standard cables Improper Network Topologies www.hp.com/go/procurve/ manuals Check the port configuration Diagnosing with the LEDs LED patterns for General Switch Troubleshooting Diagnostic Tips: Page procurve/manuals, (See page 1-13) LED Patterns for PoE Troubleshooting Proactive Networking Hardware Diagnostic Tests Testing the Switch by Resetting It Testing Twisted-PairCabling Testing Switch-to-DeviceNetwork Communications Testing End-to-EndNetwork Communications Restoring the Factory Default Configuration Downloading New Switch Software HP Customer Support Services Before Calling Support Page Switch Specifications Physical Electrical Environmental Acoustics RPS/EPS Connectors Cable Length Safety Cabling and Technology Information Cabling specifications Technology distance specifications Mode Conditioning Patch Cord Installing the Patch Cord Twisted-PairCable/Connector Pin-Outs Other Wiring Rules: Straight-through Twisted-PairCable for 10 Mbps or 100 Mbps Network Connections Crossover Twisted-PairCable for 10 Mbps or 100 Mbps Network Connection Straight-Through Twisted-PairCable for 1000 Mbps Network Connections Safety and EMC Regulatory Statements Safety Information Informations concernant la sécurité Hinweise zur Sicherheit Considerazioni sulla sicurezza Consideraciones sobre seguridad Safety Information (Japan) Safety Information (China) EMC Regulatory Statements Canada Australia/New Zealand Japan Korea Taiwan European Community Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Page Page Page Index Numerics Page Page Page Page Technology for better business outcomes To learn more, visit www.hp.com/go/procurve *5991-8573