HP FET MULTIPLEXER E1351A/53A guide

s

Appendix C

HP E1351A/53A FET Multiplexer Error Messages

Table C-1 lists the error messages associated with the multiplexer modules programmed with SCPI commands. See the HP E1406A Command Module User’s Manual for complete information on error messages.

Table C-1. 16-Channel FET Multiplexer Error Messages

No.	Title	Potential Causes


–211	Trigger Ignored	Trigger received when scan not enabled. Trigger received after scan
		complete. Trigger too fast.

–213	INIT Ignored	Attempting to execute an INIT command when a scan is already in
		progress.

–224	Illegal Parameter Value	Attempting to execute a command with a parameter not applicable to the
		command.

1500	External Trigger Source Already	Assigning an external trigger source to a switchbox when the trigger
	Allocated	source has already been assigned to another switchbox.

2000	Invalid Card Number	Addressing a module (card) in a switchbox that is not part of the
		switchbox.

2001	Invalid Channel Number	Attempting to address a channel of a module in a switchbox that is not
		supported by the module (for example, ch. 99 of multiplexer module).

2006	Command Not Supported On	Sending a command to a module (card) in a switchbox that is
	This Card	unsupported by the module.

2008	Scan List Not Initialized	Executing a Scan without the INIT command.

2009	Too Many Channels in Channel	Attempting to address more channels than available in the switchbox.
	List

2010	Scan Mode Not Allowed On	Attempting to execute a SCAN:MODE which is not supported.
	Thi Card.

2011	Empty Channel List	No valid channels in <channel_list>.

2012	Invalid Channel Range	Invalid channel(s) specified in SCAN <channel_list> command.
		Attempting to begin scanning when no valid channel list is defined.

2017	Incorrect ARM:COUNt	Attempting to run a downloaded scan list with ARM:COUNt set to value
		other than 1.

2600	Function Not Supported On	Sending a command to a module (card) in a switchbox that is not
	This Card	supported by the module or switchbox.

2601	Channel List Required	Sending a command requiring a channel list without the channel list.

Appendix C

HP E1351A/53A FET Multiplexer Error Messages 99

Image 99

HP FET MULTIPLEXER E1351A/53A manual HP E1351A/53A FET Multiplexer Error Messages

Contents

Contents Understanding the HP E1351A/53A FET Multiplexer Modules Appendix C.HP E1351A/53A FET Multiplexer Error Messages HP E1351A/53A FET Multiplexer User’s Manual Contents Certification Documentation History According to ISO/IEC Guide 22 and EN July 20Page Business Reply Mail Page FET Multiplexer Module Description Using This Chapter Multimeter Connection Points Analog Bus Connector FET Multiplexer Module Block Diagram Output 70903OUTP on Switchbox and Scanning Voltmeter Configurations Digital Bus and Triggering Initial Operation Programming Language Configuring the HP E1351A/53A FET Multiplexer Modules Multiplexer Card Numbers Card Numbers for Single-Module Switchboxes Card Numbers for Scanning Voltmeter Setting the Address Switch Selecting the Interrupt Line Number Setting the Interrupt Line Number Card ID Switch Setting the Card ID Switch Channel FET Multiplexer Connector Pin-out Connecting User Inputs Signal Conditioning Components/Current Shunts Adding Signal Conditioning Components/Current Shunts Wiring Guidelines Connecting Field Wiring Wiring a Terminal Module 10. Analog Bus and Digital Bus Connections Connecting Multimeters and Signal Generators 11. Analog Bus and Digital Bus Cables Analog Bus and Digital Bus CablesPage Selecting Channels Using the HP E1351A/53A FET Multiplexer Modules Using the HP E1351A/53A FET Multiplexer Modules Chapter Matrix Commands Used in Chapter Multiplexer Commands Scanport None Connecting Switchbox Channels to Direct Terminals CLOS? Closing Channels 02 and 09 for a Voltage Measurement Connecting Channels 02 and 10 for 4-Wire Ohms Measurement Example Making Voltage Measurements By Scanning Scanning a Range of Switchbox Channels Scanning Channels 100 to 215 of a Two-Module Switchbox Example Making 4-Wire Ohms Measurements by Scanning Example Making 2-Wire Ohms Measurements by Scanning Downloading a Scan List Output 70904INIT Scanning a Switchbox without a Downloaded Scan List Output 70904STATOPERENAB Scanning a Switchbox with a Downloaded Scan List Connecting the Analog Bus and Digital Bus Cables Scanning Voltmeter Configuration with HP E1326B Temperature Measurement Using a Thermocouple Using the HP E1351A/53A FET Multiplexer Modules Chapter Commands for Scanning Switchbox Channels Using Scanning Trigger SourcesScanning with External Instruments Scanning Commands Trigger Sources Example Scanning With External Instruments Output 70914OUTP on Example Scanning Using Trig Out Event In Ports Output 722TRIG Extdcvmem Fifo SCANMODE, Scanport and TRIGgerSOURce Dbus Example Scan Complete Monitor Using the Scan Complete Bit Command Types Common Command FormatScpi Command Format ROUTeSCANMODE Volt Scpi Command Reference ABORt Subsystem SyntaxExample Stopping a Scan with ABORt Example Query Number of Scanning Cycles COUNtParameters Comments Example Select Module #2 in a Switchbox for Monitoring DISPlayMONitorCARD Mode Example Enabling the Monitor Mode CONTinuous INITiate Example Query Continuous Scanning State Example Enabling Continuous Scans Example Enabling Trig Out Port OUTPutSTATe ∙ Downloaded Scans The OUTPut subsystem does not work with ∙ Closing Channels To close ROUTe ∙ Opening Channels To open ∙ Query is Software Readback The ROUTeCLOSe? commandExample Closing Multiplexer Channels Example Query Multiplexer Channel Closure Query Multiplexer Channel Open State ∙ Query is Software Readback The ROUTeOPEN? commandExample Opening Multiplexer Channels ∙ Scanning Operation With a valid channel list Example Scanning Using External Instruments Example Query Scan Mode Example Query Scan Port Example Selecting the Abus Port Example Set and Query the SETTling Time Example Setting 16 μsec SETTling Time OPERationENABle Example Enable the Status Register BitSTATus Example Reading the Description of Card #1 Module SYSTemCDEScription? ∙ 16-Channel FET Multiplexer Module Description Example Reading the Model Number of a Card #1 Module Comments ∙ 16-Channel FET Multiplexer Module Model Number IMMediate ∙ Executing the TRIGgerIMMediate Command a channel listExample Advancing Scan using the TRIGger Command TRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command ∙ Enabling the Trigger Source The TRIGgerSOURce command Example Scanning Using External Triggers Scanning Using Bus TriggersExample Query Trigger Source ANSI/IEEE Standard Ieee 488.2 Common Commands Scpi Commands Quick Reference Description Command Quick ReferencePage Power Off High to Low Maximum Voltage Screw Terminal Wire Size Watts/SlotConnectors Used P1 Maximum Offset Voltage Number of Slots Input Impedance Power Requirements HP E1351A/53A FET Multiplexer Specifications Appendix a Register Addressing About This Appendix HP E1351A/53A Register-Based Programming Appendix B A16 Address Space Inside Command Module Or Mainframe A16 Address Space Outside Command Module Or Mainframe Register Descriptions Device Type Register Register Bit Descriptions Register moduleManufacturer ID Register Status/Control Register Enable IRQ EN Scan Channel Delay Register Continuous Enable CNT EN Reset Pointer RST PTRScan Control Register C1 C0 Scan Channel Configuration RegisterDirect Channel Configuration Register A Tree Isolation Switch Disable A-D Valid Channel VLD Direct Control Register Executing Commands ROUTe ROUTeCLOSe channellist is equivalent to the following HP E1351A/53A Register-Based Programming Appendix B Register-Based Programming for Maximum Speed Decimal code Appendix B HP E1351A/53A Register-Based Programming Table B-1. Multimeter Command and Parameter Opcodes Multimeter Command Parameter Opcodes Figure B-3. Configuring the Multimeter Error Code Cause Multimeter Register-Based Programming Error Codes HP E1351A/53A FET Multiplexer Error Messages HP E1351A/53A FET Multiplexer Error Messages Appendix C Laddr Index HP E1351A/53A FET Multiplexer User’s Manual Index HP-IB HP E1351A/53A FET Multiplexer User’s Manual Index HP E1351A/53A FET Multiplexer User’s Manual Index HP E1351A/53A FET Multiplexer User’s Manual Index HP E1351A/53A FET Multiplexer User’s Manual Index