Manuals / HP / Computer Equipment / Computer Accessories

HP XP10000, XP128 manual Disk array device emulations

Models: XP10000

1 82

Download 82 pages 60.77 Kb

Page 61

Disk array device emulations

B

Disk array device emulations

This appendix provides information about supported emulations and device type specifications. Some parameters may not be relevant to your array. Consult your HP representative for information about supported configurations for your system.

Disk array device emulations

63

Image 61

HP XP10000, XP128 manual Disk array device emulations

Contents

XP128 XP1024 XP10000 XP12000 HP-UXsixth edition July part number A5951-96015 HP StorageWorks Disk Array XP operating system configuration guideHP-UX is a registered trademark of Hewlett-Packard Company 1 Installation ContentsWorksheets TroubleshootingDisk array device emulations IndexIntended audience About this guidePrerequisites Disk arraysHP storage website Related documentationHP sales and authorized resellers HP StorageWorks Disk Array XP128 Owner’s GuideHP technical support Italics Document conventionsBlue text Figure BoldRevision history Warranty statement LIMITATION OF LIABILITY. EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT INCLUDING NEGLIGENCE WILL HP OR ITS SUBSIDIARIES, AFFILIATES, DIRECTORS, OFFICERS, EMPLOYEES, AGENTS OR SUPPLIERS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR OTHER DAMAGES INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS, ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE SOFTWARE, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Your use of the Software is entirely at your own risk. Should the Software prove defective, you assume the entire cost of all service, repair or correction. Some jurisdictions do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you to the extent prohibited by such local laws Page Installation InstallationFeatures and requirements Fibre Channel interface Failover Device emulation typesRAID Manager command devices SNMP configurationInstallation procedures Setting the host mode for the disk array ports Install and configure the disk arrayPage Installation Setting the System Option ModesMode LevelFibre Address Configuring the Fibre Channel portsFabric and Connection parameter settings Installing and configuring the HBAs Install and configure the hostLoading the OS and software Clustering and fabric zoning Environment Fabric zoning and LUN security for multiple operating systemsOS Mix Fabric ZoningDefining the paths Connect the disk arrayIn Command View XP AE, LUN mapping includes Configuring ports Example Verifying HBA installationInstallation To verify device recognition Verifying device recognitionExample x = SCSI bus instance number y = SCSI target ID z = LUN cxtydz whereExample different address for each port, reboot the server, and then verify new device recognition again Configure disk array devices Verifying the device files and drivers This task can also be accomplished with the lssf command Example Exampleinsf Installing special files for mux2 instance Creating the device filesExample cxtydz whereExample Example 0xxxyz00 where xx = SCSI bus instance number y = SCSI target IDIf you need to delete a device file, use the rm -i command Example of a completed device data tableTo create the physical volumes Creating the physical volumesTo create volume groups Creating new volume groupsIn this example group name = vg06, major number of group file = each volume group, and c = characterminor number of existing group file = 06 which must be unique for 7. Create the volume groupdev/dsk/c6t0d0 To create logical volumes Creating logical volumeslvremove Example lvremove /dev/vgnn/lvolxExample OPEN-L =Example Creating the file systemsTo create file systems Example Example 2. Repeat step 1 for each logical volume on the disk arrayTo change the I/O timeout parameter Setting the I/O timeout parameterTo create a mount directory for each logical volume Creating the mount directoriesTo mount and verify the file systems Mounting and verifying the file systemsExample Example To set up and verify the auto-mount parameters Setting and verifying the auto-mount parametersExample Device to mount Page Troubleshooting TroubleshootingError conditions with vgcreate pvcreate for example, /dev/rdsknewfs for example, /dev/vg01/r/vo/x The host hangs or devices are Contact Information Calling the HP support centerBefore you call Page Worksheets WorksheetsPath worksheet Disk array device emulations Disk array device emulationsOPEN Supported emulationsOPEN LUSESector Device type specificationsSectors Device TypeNote 1 The availability of a disk type depends on the disk array Example For a CVS LUSE volume with capacity = 37 MB and n = Physical LUSE device parametersphysical extentphysical Physicalextent extent sizephysical Physicalextent extent sizeSCSI TID map for Fibre Channel adapters The mapping cannot be done when these conditions exist Reference information for SAM To configure the newly installed SCSI disk devices Configuring the devices using SAM1. Select Disks and File Systems, then select Disk Devices 4. In the Add a Disk Using LVM window, select Create... or Extend a Volume Group To change the maximum number of volume groups Setting the maximum number of volume groups using SAMGlossary disk controller unit LDEV Volume size customization. Synonymous with CVS support representatives onlyIndex Page Page cannot be created 57 creating 41 creating groups W warranty web site setting maximum number 76 logicalgroups cannot be created 57 creating auto-mount parameters 52 cannot be created 57 creating