Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna manual Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C, Operator´s manual

Models: 13 AWD 15 C

1 56

Download 56 pages 24.42 Kb

Page 1

Image 1

Operator´s manual

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C

Please read these instructions carefully and make sure you understand them before using the machine.

English

Page 1

Image 1

Husqvarna manual Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C, Operator´s manual, English

Contents

Operator´s manual Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 CEnglish Page Rider 13 C, Rider 13 AWD and Rider 15 C CONTENTS Operator’s Manual for Rider 11, Rider 11 CIMPORTANT INFORMATION Dear customer INTRODUCTIONTravel and transport on public roads TowingSerial number Good serviceINTRODUCTION EXPLANATION OF SYMBOLS Safety instructions SAFETY INSTRUCTIONSGeneral use Read the operator’s manual before startingPersonal protective equipment Keep children away from the area to be mowedSAFETY INSTRUCTIONS Make sure that you have first aid equipmentDriving on slopes Be especially careful when driving on slopesProceed as follows Mow upwards and downwards on slopes, not sideways6003-004Children MaintenanceNever allow children to operate the machine Never fill the fuel tank indoorsThe engine and the exhaust system become very hot during operation Do not smoke when carrying out maintenanceRisk of burn injuries if touched SAFETY INSTRUCTIONSTransport Regularly clean grass, leaves and other debrisNever run the machine in an enclosed area from the machinePresentation PRESENTATIONLocation of the controls Throttle and Choke lever PRESENTATION RIDER 11, 11 CClutch pedal Brake pedal / Parking brakeSpeed limiter PRESENTATION RIDER 13 C, 13 AWD, 15 CParking brake Throttle and Choke leverLift lever for cutting unit Cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionSeat Lever for adjustment of cutting heightFuelling PRESENTATIONBefore starting DRIVINGStarting the engine Impaired cooling of the engine. Risk of major engine damageWarm engine Cold engineDRIVING 5. Set the throttle control midway between position 1 andTo attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order Jumper cables connection2. For Rider 13 C, Rider 13 AWD and Rider 15 C Driving the machineFor Rider 11 and Rider 11 C The clutch must be used for each gear changeMowing pattern Cutting tipsDRIVING IMPORTANT INFORMATIONStopping the engine Hill start, manual gearboxNever drive the machine on ground with a slope of more thanRelease lever Rider 13 AWD Release lever Rider 13 C, Rider 13 AWD and Rider 15 CRear Axle Rider 13 AWD rearMaintenance schedule MAINTENANCEThe engine is switched off The ignition key is removed The ignition cable is removed from the plugAvoid using a high pressure washer or a steam cleaner CleaningMAINTENANCE IMPORTANT INFORMATIONEngine hood Dismantling of the machine hoodsFront hood Rider Front hood Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 CRight-hand fender Inspecting the silencerLeft-hand fender MAINTENANCEMAINTENANCE Checking and adjustment of the steering wiresCheck and adjust the brakes on Rider 13 C and Rider 15 C Adjusting the brake Rider 11 and Rider 11 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CA poorly adjusted parking brake can result in reduced braking ability Adjusting the Parking Brake Rider 13 AWDMAINTENANCE Replacement of the fuel filter Adjustment of the throttle wireMAINTENANCE Replacing the air filter Do not use compressed air to clean the paper filterFilters should not be oiled. They should be assembled dry MAINTENANCEProcedures on contact with acid Check the level of the battery acidIgnition system Checking of the fuel pump’s air filterRider 13 C Rider 15 C Inspecting the safety systemMAINTENANCE Rider 11 Rider 11 CMAINTENANCE Rider 13 AWDInspecting the safety system 34- EnglishChecking the tyre pressure Main fuseCheck the engine’s cooling air intake Air intake grille Cooling air intakeMAINTENANCE Checking the cutting unit’s parallelism36- English Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderMAINTENANCE Service position for BioClip MAINTENANCE RIDER 11C,13C, 13 AWD,15CPlacing in service position 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCE RIDER 11C,13C, 13 AWD,15CTake care not to get your hand trapped Restoring from service positionMAINTENANCE RIDER 11C,13C, 13 AWD,15C Cutting unit with rear ejection Checking the bladesCombi MAINTENANCECheck the engine’s oil level LUBRICATIONChanging the oil IMPORTANT INFORMATIONRider 13 C, Rider 13 AWD and Rider 15 C Check the transmission’s oil levelLubrication of belt tensioner 2. Rider 13 C, Rider 15 CGeneral lubrication Lubrication Rider 11 and Rider 11 CLubrication of front wheel bearings Check that the lock-ring is correctly positioned in the slotProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage CoverDimensions TECHNICAL DATARider EngineTECHNICAL DATA Rider 13 CDimensions EngineTECHNICAL DATA Rider 15 CDimensions EngineEU declaration of conformity Only applies to Europe EU-DECLARATION OF CONFORMITYPre-delivery service SERVICEJOURNALAfter first 5 hours Work doneSERVICEJOURNAL ´z+R-h¶6D¨Work done Date, mileage, stamp, signEnglish 115 ´z+R-h¶6D¨ 2005W46