Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 15 C, 13 AWD Restoring from service position, Take care not to get your hand trapped

Models: 13 AWD 15 C

1 56

Download 56 pages 24.42 Kb

Page 42

Image 42

MAINTENANCE RIDER 11C,13C, 13 AWD,15C

WARNING!

Take care not to get your hand trapped.

8.Lift off the drive belt (1). Then pull out the pin (2).

9. Pull the frame forwards and refit the pin.

2 Manual background

6017-225

6017-226

10.Grasp the front edge of the cutting unit, pull out and raise into the service position.

If the cylindrical bolt, which is now holding the cutting unit is removed, the cutting unit can be lifted off.

Restoring from service position

To leave the service position, reverse the procedures set out in ”Placing in the service position”. Make sure that the cutting unit’s ”lug” enters the loop correctly on the underside of the machine, see diagram.

6017-227

8009-438

40– English

Page 42

Image 42

Husqvarna 15 C, 13 AWD manual Restoring from service position, Take care not to get your hand trapped

Contents

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Operator´s manualEnglish Page CONTENTS Operator’s Manual for Rider 11, Rider 11 C Rider 13 C, Rider 13 AWD and Rider 15 CIMPORTANT INFORMATION Travel and transport on public roads INTRODUCTIONDear customer TowingGood service Serial numberINTRODUCTION EXPLANATION OF SYMBOLS General use SAFETY INSTRUCTIONSSafety instructions Read the operator’s manual before startingSAFETY INSTRUCTIONS Keep children away from the area to be mowedPersonal protective equipment Make sure that you have first aid equipmentProceed as follows Be especially careful when driving on slopesDriving on slopes Mow upwards and downwards on slopes, not sideways6003-004Never allow children to operate the machine MaintenanceChildren Never fill the fuel tank indoorsRisk of burn injuries if touched Do not smoke when carrying out maintenanceThe engine and the exhaust system become very hot during operation SAFETY INSTRUCTIONSNever run the machine in an enclosed area Regularly clean grass, leaves and other debrisTransport from the machinePRESENTATION PresentationLocation of the controls Clutch pedal PRESENTATION RIDER 11, 11 CThrottle and Choke lever Brake pedal / Parking brakeParking brake PRESENTATION RIDER 13 C, 13 AWD, 15 CSpeed limiter Throttle and Choke leverLifting of the cutting unit transport position Cutting unitLift lever for cutting unit Lowering of the cutting unit cutting positionFuelling Lever for adjustment of cutting heightSeat PRESENTATIONStarting the engine DRIVINGBefore starting Impaired cooling of the engine. Risk of major engine damageDRIVING Cold engineWarm engine 5. Set the throttle control midway between position 1 andTo remove cables, reverse order To start an engine with a weak batteryTo attach jumper cables Jumper cables connectionFor Rider 11 and Rider 11 C Driving the machine2. For Rider 13 C, Rider 13 AWD and Rider 15 C The clutch must be used for each gear changeDRIVING Cutting tipsMowing pattern IMPORTANT INFORMATIONNever drive the machine on Hill start, manual gearboxStopping the engine ground with a slope of more thanRear Axle Release lever Rider 13 C, Rider 13 AWD and Rider 15 CRelease lever Rider 13 AWD Rider 13 AWD rearThe engine is switched off The ignition key is removed MAINTENANCEMaintenance schedule The ignition cable is removed from the plugMAINTENANCE CleaningAvoid using a high pressure washer or a steam cleaner IMPORTANT INFORMATIONFront hood Rider Dismantling of the machine hoodsEngine hood Front hood Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 CLeft-hand fender Inspecting the silencerRight-hand fender MAINTENANCEChecking and adjustment of the steering wires MAINTENANCEPoorly adjusted brakes can result in reduced braking power Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD A poorly adjusted parking brake can result in reduced braking abilityMAINTENANCE Adjustment of the throttle wire Replacement of the fuel filterMAINTENANCE Filters should not be oiled. They should be assembled dry Do not use compressed air to clean the paper filterReplacing the air filter MAINTENANCEIgnition system Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterMAINTENANCE Inspecting the safety systemRider 13 C Rider 15 C Rider 11 Rider 11 CInspecting the safety system Rider 13 AWDMAINTENANCE 34- EnglishCheck the engine’s cooling air intake Main fuseChecking the tyre pressure Air intake grille Cooling air intakeChecking the cutting unit’s parallelism MAINTENANCE36- English Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugMAINTENANCE MAINTENANCE RIDER 11C,13C, 13 AWD,15C Service position for BioClipPlacing in service position MAINTENANCE RIDER 11C,13C, 13 AWD,15C 5. Disengage the spring from the drive belt tensioning wheelRestoring from service position Take care not to get your hand trappedMAINTENANCE RIDER 11C,13C, 13 AWD,15C Combi Checking the bladesCutting unit with rear ejection MAINTENANCEChanging the oil LUBRICATIONCheck the engine’s oil level IMPORTANT INFORMATIONLubrication of belt tensioner Check the transmission’s oil levelRider 13 C, Rider 13 AWD and Rider 15 C 2. Rider 13 C, Rider 15 CLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Check that the lock-ring is correctly positioned in the slotTROUBLE SHOOTING SCHEDULE ProblemProcedure Winter storage ServiceSTORAGE CoverRider TECHNICAL DATADimensions EngineDimensions Rider 13 CTECHNICAL DATA EngineDimensions Rider 15 CTECHNICAL DATA EngineEU-DECLARATION OF CONFORMITY EU declaration of conformity Only applies to EuropeAfter first 5 hours SERVICEJOURNALPre-delivery service Work doneWork done ´z+R-h¶6D¨SERVICEJOURNAL Date, mileage, stamp, signEnglish ´z+R-h¶6D¨ 2005W46 115