Operator´s manual
Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C
English
Page
Rider 13 C, Rider 13 AWD and Rider 15 C
CONTENTS Operator’s Manual for Rider 11, Rider 11 C
IMPORTANT INFORMATION
Travel and transport on public roads
INTRODUCTION
Dear customer
Towing
Serial number
Good service
INTRODUCTION
EXPLANATION OF SYMBOLS
General use
SAFETY INSTRUCTIONS
Safety instructions
Read the operator’s manual before starting
SAFETY INSTRUCTIONS
Keep children away from the area to be mowed
Personal protective equipment
Make sure that you have first aid equipment
Proceed as follows
Be especially careful when driving on slopes
Driving on slopes
Mow upwards and downwards on slopes, not sideways6003-004
Never allow children to operate the machine
Maintenance
Children
Never fill the fuel tank indoors
Risk of burn injuries if touched
Do not smoke when carrying out maintenance
The engine and the exhaust system become very hot during operation
SAFETY INSTRUCTIONS
Never run the machine in an enclosed area
Regularly clean grass, leaves and other debris
Transport
from the machine
Presentation
PRESENTATION
Location of the controls
Clutch pedal
PRESENTATION RIDER 11, 11 C
Throttle and Choke lever
Brake pedal / Parking brake
Parking brake
PRESENTATION RIDER 13 C, 13 AWD, 15 C
Speed limiter
Throttle and Choke lever
Lifting of the cutting unit transport position
Cutting unit
Lift lever for cutting unit
Lowering of the cutting unit cutting position
Fuelling
Lever for adjustment of cutting height
Seat
PRESENTATION
Starting the engine
DRIVING
Before starting
Impaired cooling of the engine. Risk of major engine damage
DRIVING
Cold engine
Warm engine
5. Set the throttle control midway between position 1 and
To remove cables, reverse order
To start an engine with a weak battery
To attach jumper cables
Jumper cables connection
For Rider 11 and Rider 11 C
Driving the machine
2. For Rider 13 C, Rider 13 AWD and Rider 15 C
The clutch must be used for each gear change
DRIVING
Cutting tips
Mowing pattern
IMPORTANT INFORMATION
Never drive the machine on
Hill start, manual gearbox
Stopping the engine
ground with a slope of more than
Rear Axle
Release lever Rider 13 C, Rider 13 AWD and Rider 15 C
Release lever Rider 13 AWD
Rider 13 AWD rear
The engine is switched off The ignition key is removed
MAINTENANCE
Maintenance schedule
The ignition cable is removed from the plug
MAINTENANCE
Cleaning
Avoid using a high pressure washer or a steam cleaner
IMPORTANT INFORMATION
Front hood Rider
Dismantling of the machine hoods
Engine hood
Front hood Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 C
Left-hand fender
Inspecting the silencer
Right-hand fender
MAINTENANCE
Checking and adjustment of the steering wires
MAINTENANCE
Poorly adjusted brakes can result in reduced braking power
Adjusting the brake Rider 11 and Rider 11 C
Check and adjust the brakes on Rider 13 C and Rider 15 C
Checking the brake Rider 11 and Rider 11 C
A poorly adjusted parking brake can result in reduced braking ability
Adjusting the Parking Brake Rider 13 AWD
MAINTENANCE
Replacement of the fuel filter
Adjustment of the throttle wire
MAINTENANCE
Filters should not be oiled. They should be assembled dry
Do not use compressed air to clean the paper filter
Replacing the air filter
MAINTENANCE
Ignition system
Check the level of the battery acid
Procedures on contact with acid
Checking of the fuel pump’s air filter
MAINTENANCE
Inspecting the safety system
Rider 13 C Rider 15 C
Rider 11 Rider 11 C
Inspecting the safety system
Rider 13 AWD
MAINTENANCE
34- English
Check the engine’s cooling air intake
Main fuse
Checking the tyre pressure
Air intake grille Cooling air intake
MAINTENANCE
Checking the cutting unit’s parallelism
36- English
Removing the mulching plug
Adjustment of the cutting unit’s parallelism for the Rider
MAINTENANCE
Service position for BioClip
MAINTENANCE RIDER 11C,13C, 13 AWD,15C
Placing in service position
MAINTENANCE RIDER 11C,13C, 13 AWD,15C
5. Disengage the spring from the drive belt tensioning wheel
Take care not to get your hand trapped
Restoring from service position
MAINTENANCE RIDER 11C,13C, 13 AWD,15C
Combi
Checking the blades
Cutting unit with rear ejection
MAINTENANCE
Changing the oil
LUBRICATION
Check the engine’s oil level
IMPORTANT INFORMATION
Lubrication of belt tensioner
Check the transmission’s oil level
Rider 13 C, Rider 13 AWD and Rider 15 C
2. Rider 13 C, Rider 15 C
Lubrication of front wheel bearings
Lubrication Rider 11 and Rider 11 C
General lubrication
Check that the lock-ring is correctly positioned in the slot
Problem
TROUBLE SHOOTING SCHEDULE
Procedure
Winter storage
Service
STORAGE
Cover
Rider
TECHNICAL DATA
Dimensions
Engine
Dimensions
Rider 13 C
TECHNICAL DATA
Engine
Dimensions
Rider 15 C
TECHNICAL DATA
Engine
EU-DECLARATION OF CONFORMITY
EU declaration of conformity Only applies to Europe
After first 5 hours
SERVICEJOURNAL
Pre-delivery service
Work done
Work done
´z+R-h¶6D¨
SERVICEJOURNAL
Date, mileage, stamp, sign
English
´z+R-h¶6D¨ 2005W46
115