6017-221 8009-583 8009-122 6017-223 | Husqvarna 13 AWD, 15 C

MAINTENANCE RIDER 11C,13C, 13 AWD,15C

4.Fit the support wheels on either side of the rear of the cutting unit.

WARNING!

Wear protective glasses when dismantling the cutting unit. The spring which tensions up the belt can go off and cause personal injury.

5.Disengage the spring from the drive belt tensioning wheel.

6.Place a foot on the front edge of the cutting unit near the wheel and raise the front edge of the unit to make it easier to remove the lift strut.

7.Engage the strut in the holder.

6017-221

8009-583

8009-122

6017-223

English – 39

Image 41

Husqvarna 13 AWD, 15 C manual 6017-221 8009-583 8009-122 6017-223

Contents

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Dear customer IntroductionTravel and transport on public roads Towing Serial number Good service Slope Explanation of Symbols General use Safety Instructions Keep children away from the area to be mowed Proceed as follows Driving on slopes Children Maintenance Do not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Throttle and Choke lever Presentation Rider 11, 11 CClutch pedal Brake pedal / Parking brake Parking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Lift lever for cutting unit Cutting unit Fuelling Lever for adjustment of cutting heightSeat Before starting DrivingStarting the engine Rider 13 AWD Warm engine Cold engine To remove cables, reverse order To start an engine with a weak battery For Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Stopping the engine Hill start, manual gearbox Release lever Rider 13 AWD Release lever Rider 13 C, Rider 13 AWD Rider 15 CRear Axle Front Axle Maintenance schedule Maintenance Avoid using a high pressure washer or a steam cleaner Cleaning Front hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Check and adjust the brakes on Rider 13 C and Rider 15 C Adjusting the brake Rider 11 and Rider 11 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 C Adjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wire Replacing the air filter Procedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engine Inspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the Rider Placing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service position Checking the blades Changing the oil LubricationCheck the engine’s oil level Rider 13 C, Rider 15 C Lubrication of belt tensioner Lubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Problem Procedure Trouble Shooting Schedule Storage ServiceWinter storage Cover Technical Data Electrical system Dimensions Rider 13 C Dimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of Conformity Pre-delivery service ServicejournalAfter first 5 hours Work done Work done Date, mileage, stamp, sign English 115 01