Checking and adjustment of the steering wires | Husqvarna 13 AWD

MAINTENANCE

Checking and adjustment of the steering wires

The steering is controlled by means of wires.

These can in time become slack, which implies that the adjustment of the steering becomes altered.

Check and adjust the steering as follows:

1.Dismantle the frame-plate by releasing the screws (two on each side).

8009-578

2.Check the tension of the steering wires by pushing them together as shown in the diagram. It should be possible to push them together so that the distance between them is half as much, without using unnecessary force.

3.If necessary, the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar. Do not tension the wires too much, they should only be tightened against the steering collar.

Support the wire so it does not twist.

If you only tension one side the steering wheel’s centre position may change.

Check the wire tension as set out in point 2 after you have made the adjustment.

6008-009

8009-579

English – 27

Image 29

Husqvarna 13 AWD, 15 C manual Checking and adjustment of the steering wires

Contents

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Dear customer IntroductionTravel and transport on public roads Towing Serial number Good service Slope Explanation of Symbols General use Safety Instructions Keep children away from the area to be mowed Proceed as follows Driving on slopes Children Maintenance Do not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Throttle and Choke lever Presentation Rider 11, 11 CClutch pedal Brake pedal / Parking brake Parking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Lift lever for cutting unit Cutting unit Fuelling Lever for adjustment of cutting heightSeat Before starting DrivingStarting the engine Rider 13 AWD Warm engine Cold engine To remove cables, reverse order To start an engine with a weak battery For Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Stopping the engine Hill start, manual gearbox Release lever Rider 13 AWD Release lever Rider 13 C, Rider 13 AWD Rider 15 CRear Axle Front Axle Maintenance schedule Maintenance Avoid using a high pressure washer or a steam cleaner Cleaning Front hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Check and adjust the brakes on Rider 13 C and Rider 15 C Adjusting the brake Rider 11 and Rider 11 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 C Adjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wire Replacing the air filter Procedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engine Inspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the Rider Placing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service position Checking the blades Changing the oil LubricationCheck the engine’s oil level Rider 13 C, Rider 15 C Lubrication of belt tensioner Lubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Problem Procedure Trouble Shooting Schedule Storage ServiceWinter storage Cover Technical Data Electrical system Dimensions Rider 13 C Dimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of Conformity Pre-delivery service ServicejournalAfter first 5 hours Work done Work done Date, mileage, stamp, sign English 115 01