Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 15 C, 13 AWD manual ´z+R-h¶6D¨ 2005W46, 115

Models: 13 AWD 15 C

1 56

Download 56 pages 24.42 Kb

Page 56

Image 56

115 01 37-26

´®z+R-h¶6D¨ 2005W46

Page 56

Image 56

Husqvarna 15 C, 13 AWD manual ´z+R-h¶6D¨ 2005W46, 115

Contents

English Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 COperator´s manual Page IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider 11, Rider 11 CRider 13 C, Rider 13 AWD and Rider 15 C INTRODUCTION Dear customerTravel and transport on public roads TowingINTRODUCTION Good serviceSerial number EXPLANATION OF SYMBOLS SAFETY INSTRUCTIONS Safety instructionsGeneral use Read the operator’s manual before startingKeep children away from the area to be mowed Personal protective equipmentSAFETY INSTRUCTIONS Make sure that you have first aid equipmentBe especially careful when driving on slopes Driving on slopesProceed as follows Mow upwards and downwards on slopes, not sideways6003-004Maintenance ChildrenNever allow children to operate the machine Never fill the fuel tank indoorsDo not smoke when carrying out maintenance The engine and the exhaust system become very hot during operationRisk of burn injuries if touched SAFETY INSTRUCTIONSRegularly clean grass, leaves and other debris TransportNever run the machine in an enclosed area from the machineLocation of the controls PRESENTATIONPresentation PRESENTATION RIDER 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brakePRESENTATION RIDER 13 C, 13 AWD, 15 C Speed limiterParking brake Throttle and Choke leverCutting unit Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionLever for adjustment of cutting height SeatFuelling PRESENTATIONDRIVING Before startingStarting the engine Impaired cooling of the engine. Risk of major engine damageCold engine Warm engineDRIVING 5. Set the throttle control midway between position 1 andTo start an engine with a weak battery To attach jumper cablesTo remove cables, reverse order Jumper cables connectionDriving the machine 2. For Rider 13 C, Rider 13 AWD and Rider 15 CFor Rider 11 and Rider 11 C The clutch must be used for each gear changeCutting tips Mowing patternDRIVING IMPORTANT INFORMATIONHill start, manual gearbox Stopping the engineNever drive the machine on ground with a slope of more thanRelease lever Rider 13 C, Rider 13 AWD and Rider 15 C Release lever Rider 13 AWDRear Axle Rider 13 AWD rearMAINTENANCE Maintenance scheduleThe engine is switched off The ignition key is removed The ignition cable is removed from the plugCleaning Avoid using a high pressure washer or a steam cleanerMAINTENANCE IMPORTANT INFORMATIONDismantling of the machine hoods Engine hoodFront hood Rider Front hood Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 CInspecting the silencer Right-hand fenderLeft-hand fender MAINTENANCEChecking and adjustment of the steering wires MAINTENANCEAdjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CMAINTENANCE Adjusting the Parking Brake Rider 13 AWDA poorly adjusted parking brake can result in reduced braking ability MAINTENANCE Adjustment of the throttle wireReplacement of the fuel filter Do not use compressed air to clean the paper filter Replacing the air filterFilters should not be oiled. They should be assembled dry MAINTENANCECheck the level of the battery acid Procedures on contact with acidIgnition system Checking of the fuel pump’s air filterInspecting the safety system Rider 13 C Rider 15 CMAINTENANCE Rider 11 Rider 11 CRider 13 AWD MAINTENANCEInspecting the safety system 34- EnglishMain fuse Checking the tyre pressureCheck the engine’s cooling air intake Air intake grille Cooling air intake36- English Checking the cutting unit’s parallelismMAINTENANCE MAINTENANCE Adjustment of the cutting unit’s parallelism for the RiderRemoving the mulching plug Placing in service position MAINTENANCE RIDER 11C,13C, 13 AWD,15CService position for BioClip MAINTENANCE RIDER 11C,13C, 13 AWD,15C 5. Disengage the spring from the drive belt tensioning wheelMAINTENANCE RIDER 11C,13C, 13 AWD,15C Restoring from service positionTake care not to get your hand trapped Checking the blades Cutting unit with rear ejectionCombi MAINTENANCELUBRICATION Check the engine’s oil levelChanging the oil IMPORTANT INFORMATIONCheck the transmission’s oil level Rider 13 C, Rider 13 AWD and Rider 15 CLubrication of belt tensioner 2. Rider 13 C, Rider 15 CLubrication Rider 11 and Rider 11 C General lubricationLubrication of front wheel bearings Check that the lock-ring is correctly positioned in the slotProcedure TROUBLE SHOOTING SCHEDULEProblem Service STORAGEWinter storage CoverTECHNICAL DATA DimensionsRider EngineRider 13 C TECHNICAL DATADimensions EngineRider 15 C TECHNICAL DATADimensions EngineEU-DECLARATION OF CONFORMITY EU declaration of conformity Only applies to EuropeSERVICEJOURNAL Pre-delivery serviceAfter first 5 hours Work done´z+R-h¶6D¨ SERVICEJOURNALWork done Date, mileage, stamp, signEnglish ´z+R-h¶6D¨ 2005W46 115