Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 15 C manual Adjusting the Parking Brake Rider 13 AWD, Maintenance

Models: 13 AWD 15 C

1 56

Download 56 pages 24.42 Kb

Page 31

Image 31

MAINTENANCE

Adjusting the Parking Brake Rider 13 AWD

Check that the parking brake is adjusted correctly by placing the machine on a slope with the front and rear axles disengaged. Apply and lock the parking brake. When the machine does not stand still, the parking brake should be adjusted accord- ing to the following.

1. Remove the left-hand wing cover.

2. Release the lock nuts (1).

3. Tension the wire with the adjusting screw (2) until all the play in the wire is taken up.

4.Tighten the lock nuts (1).

5.On completion of the adjustment the brake should be re-checked.

6. Assemble the left-hand wing cover.

WARNING!

A poorly adjusted parking brake can result in reduced braking ability.

8009-501

6021-031

English – 29

Page 31

Image 31

Husqvarna 15 C manual Adjusting the Parking Brake Rider 13 AWD, Maintenance

Contents

Operator´s manual Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 CEnglish Page Rider 13 C, Rider 13 AWD and Rider 15 C CONTENTS Operator’s Manual for Rider 11, Rider 11 CIMPORTANT INFORMATION Towing INTRODUCTIONDear customer Travel and transport on public roadsSerial number Good serviceINTRODUCTION EXPLANATION OF SYMBOLS Read the operator’s manual before starting SAFETY INSTRUCTIONSSafety instructions General useMake sure that you have first aid equipment Keep children away from the area to be mowedPersonal protective equipment SAFETY INSTRUCTIONSMow upwards and downwards on slopes, not sideways6003-004 Be especially careful when driving on slopesDriving on slopes Proceed as followsNever fill the fuel tank indoors MaintenanceChildren Never allow children to operate the machineSAFETY INSTRUCTIONS Do not smoke when carrying out maintenanceThe engine and the exhaust system become very hot during operation Risk of burn injuries if touchedfrom the machine Regularly clean grass, leaves and other debrisTransport Never run the machine in an enclosed areaPresentation PRESENTATIONLocation of the controls Brake pedal / Parking brake PRESENTATION RIDER 11, 11 CThrottle and Choke lever Clutch pedalThrottle and Choke lever PRESENTATION RIDER 13 C, 13 AWD, 15 CSpeed limiter Parking brakeLowering of the cutting unit cutting position Cutting unitLift lever for cutting unit Lifting of the cutting unit transport positionPRESENTATION Lever for adjustment of cutting heightSeat FuellingImpaired cooling of the engine. Risk of major engine damage DRIVINGBefore starting Starting the engine5. Set the throttle control midway between position 1 and Cold engineWarm engine DRIVINGJumper cables connection To start an engine with a weak batteryTo attach jumper cables To remove cables, reverse orderThe clutch must be used for each gear change Driving the machine2. For Rider 13 C, Rider 13 AWD and Rider 15 C For Rider 11 and Rider 11 CIMPORTANT INFORMATION Cutting tipsMowing pattern DRIVINGground with a slope of more than Hill start, manual gearboxStopping the engine Never drive the machine onRider 13 AWD rear Release lever Rider 13 C, Rider 13 AWD and Rider 15 CRelease lever Rider 13 AWD Rear AxleThe ignition cable is removed from the plug MAINTENANCEMaintenance schedule The engine is switched off The ignition key is removedIMPORTANT INFORMATION CleaningAvoid using a high pressure washer or a steam cleaner MAINTENANCEFront hood Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 C Dismantling of the machine hoodsEngine hood Front hood RiderMAINTENANCE Inspecting the silencerRight-hand fender Left-hand fenderMAINTENANCE Checking and adjustment of the steering wiresChecking the brake Rider 11 and Rider 11 C Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Poorly adjusted brakes can result in reduced braking powerA poorly adjusted parking brake can result in reduced braking ability Adjusting the Parking Brake Rider 13 AWDMAINTENANCE Replacement of the fuel filter Adjustment of the throttle wireMAINTENANCE MAINTENANCE Do not use compressed air to clean the paper filterReplacing the air filter Filters should not be oiled. They should be assembled dryChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Ignition systemRider 11 Rider 11 C Inspecting the safety systemRider 13 C Rider 15 C MAINTENANCE34- English Rider 13 AWDMAINTENANCE Inspecting the safety systemAir intake grille Cooling air intake Main fuseChecking the tyre pressure Check the engine’s cooling air intakeMAINTENANCE Checking the cutting unit’s parallelism36- English Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderMAINTENANCE Service position for BioClip MAINTENANCE RIDER 11C,13C, 13 AWD,15CPlacing in service position 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCE RIDER 11C,13C, 13 AWD,15CTake care not to get your hand trapped Restoring from service positionMAINTENANCE RIDER 11C,13C, 13 AWD,15C MAINTENANCE Checking the bladesCutting unit with rear ejection CombiIMPORTANT INFORMATION LUBRICATIONCheck the engine’s oil level Changing the oil2. Rider 13 C, Rider 15 C Check the transmission’s oil levelRider 13 C, Rider 13 AWD and Rider 15 C Lubrication of belt tensionerCheck that the lock-ring is correctly positioned in the slot Lubrication Rider 11 and Rider 11 CGeneral lubrication Lubrication of front wheel bearingsProblem TROUBLE SHOOTING SCHEDULEProcedure Cover ServiceSTORAGE Winter storageEngine TECHNICAL DATADimensions RiderEngine Rider 13 CTECHNICAL DATA DimensionsEngine Rider 15 CTECHNICAL DATA DimensionsEU declaration of conformity Only applies to Europe EU-DECLARATION OF CONFORMITYWork done SERVICEJOURNALPre-delivery service After first 5 hoursDate, mileage, stamp, sign ´z+R-h¶6D¨SERVICEJOURNAL Work doneEnglish 115 ´z+R-h¶6D¨ 2005W46