Main fuse, Checking the tyre pressure | Husqvarna 13 AWD, 15 C

MAINTENANCE

Main fuse

The fuse is located in a loose holder under the battery case cover, in front of the battery. Type: Flat-blade mounting, 15 A.

Do not use any other type of fuse when replacing. A blown fuse indicates that the mounting has burnt off.

Pull the fuse out of the holder when replacing. The fuse is used to pro ect the electrical system. If it blows again shortly after replacing this is due to a short circuit, which must be rectified before the machine is used again.

Checking the tyre pressure

The tyre pressure should be 60 kPa (0,6 kp/cm2 / 8.5 PSI) all round.

To improve driving the pressure on the rear tyres can be reduced to 40 kPa (0,4 kp/cm2 / 5.6 PSI). The maximum tyre pressure is 100 kPa (1,0 kp/cm2 / 14 PSI).

IMPORTANT INFORMATION

Different tyre pressures on the front tyres will result in the blades cutting the grass at different heights.

8009-370

8009-581

Check the engine’s cooling air intake

Clean the air intake grille in the engine cover behind the driver’s seat.

Fold open the engine cover.

Check that the cooling intake is free from leaves, grass and dirt.

Check the air duct, located on the inside of the engine cover, ensure it is clean and does not rub against the cooling air intake.

If the cooling intake is blocked this will interfere with the cooling of the engine, which can damage the engine.

WARNING!

The cooling air intake rotates when the engine is running. Mind your fingers.

Air intake grille

Cooling air intake

8009-431

8009-412

English – 35

Image 37

Husqvarna 13 AWD, 15 C manual Main fuse, Checking the tyre pressure, Check the engine’s cooling air intake

Contents

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Dear customer IntroductionTravel and transport on public roads Towing Serial number Good service Slope Explanation of Symbols General use Safety Instructions Keep children away from the area to be mowed Proceed as follows Driving on slopes Children Maintenance Do not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Throttle and Choke lever Presentation Rider 11, 11 CClutch pedal Brake pedal / Parking brake Speed limiter Presentation Rider 13 C, 13 AWD, 15 CParking brake Lift lever for cutting unit Cutting unit Seat Lever for adjustment of cutting heightFuelling Before starting DrivingStarting the engine Rider 13 AWD Warm engine Cold engine To remove cables, reverse order To start an engine with a weak battery For Rider 13 C, Rider 13 AWD and Rider 15 C Driving the machineFor Rider 11 and Rider 11 C Cutting tips Stopping the engine Hill start, manual gearbox Release lever Rider 13 AWD Release lever Rider 13 C, Rider 13 AWD Rider 15 CRear Axle Front Axle Maintenance schedule Maintenance Avoid using a high pressure washer or a steam cleaner Cleaning Engine hood Dismantling of the machine hoodsFront hood Rider Right-hand fender Inspecting the silencerLeft-hand fender Checking and adjustment of the steering wires Check and adjust the brakes on Rider 13 C and Rider 15 C Adjusting the brake Rider 11 and Rider 11 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 C Adjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wire Replacing the air filter Procedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engine Inspecting the safety system Rider 13 AWD Checking the tyre pressure Main fuseCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the Rider Service position for BioClip Maintenance Rider 11C,13C, 13 AWD,15CPlacing in service position 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service position Checking the blades Check the engine’s oil level LubricationChanging the oil Rider 13 C, Rider 15 C Lubrication of belt tensioner General lubrication Lubrication Rider 11 and Rider 11 CLubrication of front wheel bearings Problem Procedure Trouble Shooting Schedule Storage ServiceWinter storage Cover Technical Data Electrical system Dimensions Rider 13 C Dimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of Conformity Pre-delivery service ServicejournalAfter first 5 hours Work done Work done Date, mileage, stamp, sign English 115 01