Inspecting the safety system | Husqvarna 13 AWD, 15 C manual

MAINTENANCE

Inspecting the safety system

The Rider is equipped with a safety system that prevents starting or driving under the following conditions:

The engine should only be possible to start when the cutting unit is in its raised position and the hydrostat pedals are in the neutral position.

The driver does not need to be seated in the driver’s seat.

Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.

Check that the engine stops if you temporarily move out off the driver’s seat while the cutting unit is lowered or the hydrostat pedals are not in the neutral position.

StartmotorWorks

Ignition system

Does not work

N

Rider 11 Rider 11 C

Rider 13 C Rider 15 C

English – 33

Image 35

Husqvarna 13 AWD, 15 C manual Inspecting the safety system

Contents

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Towing IntroductionDear customer Travel and transport on public roads Serial number Good service Slope Explanation of Symbols General use Safety Instructions Keep children away from the area to be mowed Proceed as follows Driving on slopes Children Maintenance Do not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Brake pedal / Parking brake Presentation Rider 11, 11 CThrottle and Choke lever Clutch pedal Parking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Lift lever for cutting unit Cutting unit Fuelling Lever for adjustment of cutting heightSeat Rider 13 AWD DrivingBefore starting Starting the engine Warm engine Cold engine To remove cables, reverse order To start an engine with a weak battery For Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Stopping the engine Hill start, manual gearbox Front Axle Release lever Rider 13 C, Rider 13 AWD Rider 15 CRelease lever Rider 13 AWD Rear Axle Maintenance schedule Maintenance Avoid using a high pressure washer or a steam cleaner Cleaning Front hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Checking the brake Rider 11 and Rider 11 C Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Poorly adjusted brakes can result in reduced braking power Adjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wire Replacing the air filter Fitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filter Inspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the Rider Placing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service position Checking the blades Changing the oil LubricationCheck the engine’s oil level Rider 13 C, Rider 15 C Lubrication of belt tensioner Lubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Problem Procedure Trouble Shooting Schedule Cover ServiceStorage Winter storage Technical Data Electrical system Dimensions Rider 13 C Dimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of Conformity Work done ServicejournalPre-delivery service After first 5 hours Work done Date, mileage, stamp, sign English 115 01