EU-DECLARATION of Conformity | Husqvarna 15 C, 13 AWD specification

EU-DECLARATION OF CONFORMITY

EU declaration of conformity (Only applies to Europe)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that Husqvarna Rider 11, Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 C, from 2005’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVES:

-of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.

-of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.

-of May 8, 2000 ”relating to the emission of noise to surroundings” 2000/14/EC.

Information regarding noise emissions and the mowing width, see the Technical Data.

The following harmonised standards have been applied: EN292-2, EN836.

The registered body 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden has issued the report with number 01/901/001, 01/901/039, 01/901/040, 01/901/041 regarding the assessment of conformity according to annex VI to the COUNCIL’S DIRECTIVE of May 8, 2000 ”relating to the emission of noise to surroundings” 2000/14/EC.

Huskvarna Novembre 3, 2005

Roger Andersson, Development Manager/Garden Products

50– English

Image 52

Husqvarna 15 C, 13 AWD manual EU-DECLARATION of Conformity, EU declaration of conformity Only applies to Europe

Contents

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Introduction Dear customerTravel and transport on public roads Towing Good service Serial number Explanation of Symbols Slope Safety Instructions General use Keep children away from the area to be mowed Driving on slopes Proceed as follows Maintenance Children Do not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Presentation Rider 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brake Speed limiter Presentation Rider 13 C, 13 AWD, 15 CParking brake Cutting unit Lift lever for cutting unit Seat Lever for adjustment of cutting heightFuelling Driving Before startingStarting the engine Rider 13 AWD Cold engine Warm engine To start an engine with a weak battery To remove cables, reverse order For Rider 13 C, Rider 13 AWD and Rider 15 C Driving the machineFor Rider 11 and Rider 11 C Cutting tips Hill start, manual gearbox Stopping the engine Release lever Rider 13 C, Rider 13 AWD Rider 15 C Release lever Rider 13 AWDRear Axle Front Axle Maintenance Maintenance schedule Cleaning Avoid using a high pressure washer or a steam cleaner Engine hood Dismantling of the machine hoodsFront hood Rider Right-hand fender Inspecting the silencerLeft-hand fender Checking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 C Adjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filter Replacing the air filter Check the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engine Inspecting the safety system Rider 13 AWD Checking the tyre pressure Main fuseCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plug Service position for BioClip Maintenance Rider 11C,13C, 13 AWD,15CPlacing in service position 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trapped Checking the blades Check the engine’s oil level LubricationChanging the oil Lubrication of belt tensioner Rider 13 C, Rider 15 C General lubrication Lubrication Rider 11 and Rider 11 CLubrication of front wheel bearings Trouble Shooting Schedule Problem Procedure Service StorageWinter storage Cover Technical Data Dimensions Rider 13 C Electrical system Dimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to Europe Servicejournal Pre-delivery serviceAfter first 5 hours Work done Work done Date, mileage, stamp, sign English 115 01