Rider 13 AWD | Husqvarna 15 C instruction

MAINTENANCE

Inspecting the safety system

The Rider is equipped with a safety system that prevents starting or driving under the following conditions:

The engine should only be possible to start when the cutting unit is in its raised position and the hydrostat pedals are in the neutral position.

The driver does not need to be seated in the driver’s seat.

Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.

Check that the engine stops if you temporarily move out off the driver’s seat while the cutting unit is lowered or the hydrostat pedals are not in the neutral position.

StartmotorWorks

		Ignition system					Does not work

Rider 13 AWD

8009-153

34– English

Image 36

Husqvarna 15 C manual Rider 13 AWD

Contents

Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Introduction Dear customerTravel and transport on public roads Towing Good service Serial number Explanation of Symbols Slope Safety Instructions General use Keep children away from the area to be mowed Driving on slopes Proceed as follows Maintenance Children Do not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Presentation Rider 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brake Presentation Rider 13 C, 13 AWD, 15 C Speed limiterParking brake Cutting unit Lift lever for cutting unit Lever for adjustment of cutting height SeatFuelling Driving Before startingStarting the engine Rider 13 AWD Cold engine Warm engine To start an engine with a weak battery To remove cables, reverse order Driving the machine For Rider 13 C, Rider 13 AWD and Rider 15 CFor Rider 11 and Rider 11 C Cutting tips Hill start, manual gearbox Stopping the engine Release lever Rider 13 C, Rider 13 AWD Rider 15 C Release lever Rider 13 AWDRear Axle Front Axle Maintenance Maintenance schedule Cleaning Avoid using a high pressure washer or a steam cleaner Dismantling of the machine hoods Engine hoodFront hood Rider Inspecting the silencer Right-hand fenderLeft-hand fender Checking and adjustment of the steering wires Adjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 C Adjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filter Replacing the air filter Check the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engine Inspecting the safety system Rider 13 AWD Main fuse Checking the tyre pressureCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plug Maintenance Rider 11C,13C, 13 AWD,15C Service position for BioClipPlacing in service position 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trapped Checking the blades Lubrication Check the engine’s oil levelChanging the oil Lubrication of belt tensioner Rider 13 C, Rider 15 C Lubrication Rider 11 and Rider 11 C General lubricationLubrication of front wheel bearings Trouble Shooting Schedule Problem Procedure Service StorageWinter storage Cover Technical Data Dimensions Rider 13 C Electrical system Dimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to Europe Servicejournal Pre-delivery serviceAfter first 5 hours Work done Work done Date, mileage, stamp, sign English 115 01