Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 15 C, 13 AWD Inspecting the silencer, Right-hand fender, Left-hand fender, Maintenance

Models: 13 AWD 15 C

1 56

Download 56 pages 24.42 Kb

Page 28

Image 28

MAINTENANCE

Right-hand fender

Remove the screws (2 and 3) from the fender. On the Rider 13 C, Rider 13 AWD and Rider 15 C the knob (1) must also be removed.

	3
11	2
11
	8009-576

Left-hand fender

Release the screws in the fender and lift off the fender.

8009-577

Inspecting the silencer

Check regularly that the silencer is complete and secured correctly.

Temperature variations and vibrations can mean that the tightening torque for the screws drops. The screws should be checked when servicing to guarantee the correct torque. The tightening torque should be about 10 Nm. Never use a defective silencer.

WARNING!

The mufﬂer gets very hot in use and remains so for a short time afterwards. Contact can result in burns. Remember the risk of ﬁre.

8009-683

26– English

Page 28

Image 28

Husqvarna 15 C, 13 AWD manual Inspecting the silencer, Right-hand fender, Left-hand fender, Maintenance

Contents

Operator´s manual Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 CEnglish Page Rider 13 C, Rider 13 AWD and Rider 15 C CONTENTS Operator’s Manual for Rider 11, Rider 11 CIMPORTANT INFORMATION INTRODUCTION Dear customerTravel and transport on public roads TowingSerial number Good serviceINTRODUCTION EXPLANATION OF SYMBOLS SAFETY INSTRUCTIONS Safety instructionsGeneral use Read the operator’s manual before startingKeep children away from the area to be mowed Personal protective equipmentSAFETY INSTRUCTIONS Make sure that you have first aid equipmentBe especially careful when driving on slopes Driving on slopesProceed as follows Mow upwards and downwards on slopes, not sideways6003-004Maintenance ChildrenNever allow children to operate the machine Never fill the fuel tank indoorsDo not smoke when carrying out maintenance The engine and the exhaust system become very hot during operationRisk of burn injuries if touched SAFETY INSTRUCTIONSRegularly clean grass, leaves and other debris TransportNever run the machine in an enclosed area from the machinePresentation PRESENTATIONLocation of the controls PRESENTATION RIDER 11, 11 C Throttle and Choke leverClutch pedal Brake pedal / Parking brakePRESENTATION RIDER 13 C, 13 AWD, 15 C Speed limiterParking brake Throttle and Choke leverCutting unit Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionLever for adjustment of cutting height SeatFuelling PRESENTATIONDRIVING Before startingStarting the engine Impaired cooling of the engine. Risk of major engine damageCold engine Warm engineDRIVING 5. Set the throttle control midway between position 1 andTo start an engine with a weak battery To attach jumper cablesTo remove cables, reverse order Jumper cables connectionDriving the machine 2. For Rider 13 C, Rider 13 AWD and Rider 15 CFor Rider 11 and Rider 11 C The clutch must be used for each gear changeCutting tips Mowing patternDRIVING IMPORTANT INFORMATIONHill start, manual gearbox Stopping the engineNever drive the machine on ground with a slope of more thanRelease lever Rider 13 C, Rider 13 AWD and Rider 15 C Release lever Rider 13 AWDRear Axle Rider 13 AWD rearMAINTENANCE Maintenance scheduleThe engine is switched off The ignition key is removed The ignition cable is removed from the plugCleaning Avoid using a high pressure washer or a steam cleanerMAINTENANCE IMPORTANT INFORMATIONDismantling of the machine hoods Engine hoodFront hood Rider Front hood Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 CInspecting the silencer Right-hand fenderLeft-hand fender MAINTENANCEChecking and adjustment of the steering wires MAINTENANCEAdjusting the brake Rider 11 and Rider 11 C Check and adjust the brakes on Rider 13 C and Rider 15 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CA poorly adjusted parking brake can result in reduced braking ability Adjusting the Parking Brake Rider 13 AWDMAINTENANCE Replacement of the fuel filter Adjustment of the throttle wireMAINTENANCE Do not use compressed air to clean the paper filter Replacing the air filterFilters should not be oiled. They should be assembled dry MAINTENANCECheck the level of the battery acid Procedures on contact with acidIgnition system Checking of the fuel pump’s air filterInspecting the safety system Rider 13 C Rider 15 CMAINTENANCE Rider 11 Rider 11 CRider 13 AWD MAINTENANCEInspecting the safety system 34- EnglishMain fuse Checking the tyre pressureCheck the engine’s cooling air intake Air intake grille Cooling air intakeMAINTENANCE Checking the cutting unit’s parallelism36- English Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderMAINTENANCE Service position for BioClip MAINTENANCE RIDER 11C,13C, 13 AWD,15CPlacing in service position MAINTENANCE RIDER 11C,13C, 13 AWD,15C 5. Disengage the spring from the drive belt tensioning wheelTake care not to get your hand trapped Restoring from service positionMAINTENANCE RIDER 11C,13C, 13 AWD,15C Checking the blades Cutting unit with rear ejectionCombi MAINTENANCELUBRICATION Check the engine’s oil levelChanging the oil IMPORTANT INFORMATIONCheck the transmission’s oil level Rider 13 C, Rider 13 AWD and Rider 15 CLubrication of belt tensioner 2. Rider 13 C, Rider 15 CLubrication Rider 11 and Rider 11 C General lubricationLubrication of front wheel bearings Check that the lock-ring is correctly positioned in the slotProblem TROUBLE SHOOTING SCHEDULEProcedure Service STORAGEWinter storage CoverTECHNICAL DATA DimensionsRider EngineRider 13 C TECHNICAL DATADimensions EngineRider 15 C TECHNICAL DATADimensions EngineEU-DECLARATION OF CONFORMITY EU declaration of conformity Only applies to EuropeSERVICEJOURNAL Pre-delivery serviceAfter first 5 hours Work done´z+R-h¶6D¨ SERVICEJOURNALWork done Date, mileage, stamp, signEnglish ´z+R-h¶6D¨ 2005W46 115