Operator´s manual
Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C
English
Page
Rider 13 C, Rider 13 AWD and Rider 15 C
CONTENTS Operator’s Manual for Rider 11, Rider 11 C
IMPORTANT INFORMATION
Towing
INTRODUCTION
Dear customer
Travel and transport on public roads
Serial number
Good service
INTRODUCTION
EXPLANATION OF SYMBOLS
Read the operator’s manual before starting
SAFETY INSTRUCTIONS
Safety instructions
General use
Make sure that you have first aid equipment
Keep children away from the area to be mowed
Personal protective equipment
SAFETY INSTRUCTIONS
Mow upwards and downwards on slopes, not sideways6003-004
Be especially careful when driving on slopes
Driving on slopes
Proceed as follows
Never fill the fuel tank indoors
Maintenance
Children
Never allow children to operate the machine
SAFETY INSTRUCTIONS
Do not smoke when carrying out maintenance
The engine and the exhaust system become very hot during operation
Risk of burn injuries if touched
from the machine
Regularly clean grass, leaves and other debris
Transport
Never run the machine in an enclosed area
Presentation
PRESENTATION
Location of the controls
Brake pedal / Parking brake
PRESENTATION RIDER 11, 11 C
Throttle and Choke lever
Clutch pedal
Throttle and Choke lever
PRESENTATION RIDER 13 C, 13 AWD, 15 C
Speed limiter
Parking brake
Lowering of the cutting unit cutting position
Cutting unit
Lift lever for cutting unit
Lifting of the cutting unit transport position
PRESENTATION
Lever for adjustment of cutting height
Seat
Fuelling
Impaired cooling of the engine. Risk of major engine damage
DRIVING
Before starting
Starting the engine
5. Set the throttle control midway between position 1 and
Cold engine
Warm engine
DRIVING
Jumper cables connection
To start an engine with a weak battery
To attach jumper cables
To remove cables, reverse order
The clutch must be used for each gear change
Driving the machine
2. For Rider 13 C, Rider 13 AWD and Rider 15 C
For Rider 11 and Rider 11 C
IMPORTANT INFORMATION
Cutting tips
Mowing pattern
DRIVING
ground with a slope of more than
Hill start, manual gearbox
Stopping the engine
Never drive the machine on
Rider 13 AWD rear
Release lever Rider 13 C, Rider 13 AWD and Rider 15 C
Release lever Rider 13 AWD
Rear Axle
The ignition cable is removed from the plug
MAINTENANCE
Maintenance schedule
The engine is switched off The ignition key is removed
IMPORTANT INFORMATION
Cleaning
Avoid using a high pressure washer or a steam cleaner
MAINTENANCE
Front hood Rider 11 C, Rider 13 C, Rider 13 AWD and Rider 15 C
Dismantling of the machine hoods
Engine hood
Front hood Rider
MAINTENANCE
Inspecting the silencer
Right-hand fender
Left-hand fender
MAINTENANCE
Checking and adjustment of the steering wires
Checking the brake Rider 11 and Rider 11 C
Adjusting the brake Rider 11 and Rider 11 C
Check and adjust the brakes on Rider 13 C and Rider 15 C
Poorly adjusted brakes can result in reduced braking power
A poorly adjusted parking brake can result in reduced braking ability
Adjusting the Parking Brake Rider 13 AWD
MAINTENANCE
Replacement of the fuel filter
Adjustment of the throttle wire
MAINTENANCE
MAINTENANCE
Do not use compressed air to clean the paper filter
Replacing the air filter
Filters should not be oiled. They should be assembled dry
Checking of the fuel pump’s air filter
Check the level of the battery acid
Procedures on contact with acid
Ignition system
Rider 11 Rider 11 C
Inspecting the safety system
Rider 13 C Rider 15 C
MAINTENANCE
34- English
Rider 13 AWD
MAINTENANCE
Inspecting the safety system
Air intake grille Cooling air intake
Main fuse
Checking the tyre pressure
Check the engine’s cooling air intake
MAINTENANCE
Checking the cutting unit’s parallelism
36- English
Removing the mulching plug
Adjustment of the cutting unit’s parallelism for the Rider
MAINTENANCE
Service position for BioClip
MAINTENANCE RIDER 11C,13C, 13 AWD,15C
Placing in service position
5. Disengage the spring from the drive belt tensioning wheel
MAINTENANCE RIDER 11C,13C, 13 AWD,15C
Take care not to get your hand trapped
Restoring from service position
MAINTENANCE RIDER 11C,13C, 13 AWD,15C
MAINTENANCE
Checking the blades
Cutting unit with rear ejection
Combi
IMPORTANT INFORMATION
LUBRICATION
Check the engine’s oil level
Changing the oil
2. Rider 13 C, Rider 15 C
Check the transmission’s oil level
Rider 13 C, Rider 13 AWD and Rider 15 C
Lubrication of belt tensioner
Check that the lock-ring is correctly positioned in the slot
Lubrication Rider 11 and Rider 11 C
General lubrication
Lubrication of front wheel bearings
Problem
TROUBLE SHOOTING SCHEDULE
Procedure
Cover
Service
STORAGE
Winter storage
Engine
TECHNICAL DATA
Dimensions
Rider
Engine
Rider 13 C
TECHNICAL DATA
Dimensions
Engine
Rider 15 C
TECHNICAL DATA
Dimensions
EU declaration of conformity Only applies to Europe
EU-DECLARATION OF CONFORMITY
Work done
SERVICEJOURNAL
Pre-delivery service
After first 5 hours
Date, mileage, stamp, sign
´z+R-h¶6D¨
SERVICEJOURNAL
Work done
English
115
´z+R-h¶6D¨ 2005W46