Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 16 manual Inspecting the safety system, Maintenance

Models: Rider 16

1 51

Download 51 pages 44.5 Kb

Page 27

Image 27

MAINTENANCE

Inspecting the safety system

The Rider is equipped with a safety system that prevents starting or driving under the following conditions:

The engine should only be possible to start when the cutting unit is in its raised position and the hydrostat pedals are in the neutral position.

The driver does not need to be seated in the driver’s seat.

Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.

Check that the engine stops if you temporarily move out off the driver’s seat while the cutting unit is lowered or the hydrostat pedals are not in the neutral position.

Startmotor

Ignition system

Works

Does not work

26 – English

Page 27

Image 27

Husqvarna Rider 16 manual Inspecting the safety system, Maintenance

Contents

101 RiderOperator´s manual IMPORTANT INFORMATION CONTENTS Operator’s Manual for RiderII. Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers I. General operationIV. Service Danger, keep hands and feet awaySAFETY INSTRUCTIONS Towing INSTRUCTIONDear customer Travel and transport on public roadsTransmission Good serviceSerial number EngineEXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine reversingCut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes Do as followsNever allow children to drive the machine MaintenanceChildren Keep children away from the mowing areaAvoid overfilling. f fuel has been spilt on the battery can explode and cause severe injuriesClean the machine regularly from grass, leaves and other waste SAFETY INSTRUCTIONSPRESENTATION PresentationLocation of the controls Parking brake obstruct the pedals when mowingThrottle and Choke lever Speed limiterLowering of the cutting unit cutting position Cutting unitLift lever for cutting unit Lifting of the cutting unit transport positionPRESENTATION Lever for adjustment of cutting heightSeat FuellingDRIVING Starting the engineCold engine IMPORTANT INFORMATION Warm engineDRIVING 4. Set the throttle control midway between position 1 andDRIVING Driving the machineIMPORTANT INFORMATION Cutting tipsMowing pattern DRIVINGStopping the engine Release leverDRIVING Maintenance MAINTENANCEMaintenance schedule Maintenance intervalRight-hand fender Dismantling of the machine hoodsEngine hood Front hoodMAINTENANCE Checking and adjustment of the steering wiresAdjusting the brake Poorly adjusted brakes can result in reduced braking powerChecking and adjustment of the throttle wire Replacement of the fuel filterMAINTENANCE IMPORTANT INFORMATION Do not use compressed air to clean the paper filterReplacing the air filter MAINTENANCEMAINTENANCE Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterMAINTENANCE Inspecting the safety systemIMPORTANT INFORMATION Checking the tyre pressureCheck the engine’s cooling air intake MAINTENANCEInstalling BioClip Fitting the cutting unitMAINTENANCE Checking and adjustment of the cutting unit’s ground pressure Checking the cutting unit’s parallelismMAINTENANCE Adjusting the parallelism of the cutting unit Removing the cutting unitMAINTENANCE BioClip BioClip BioClip Wear gloves to protect your hands when working with the bladesReplacing the cutting unit belts Replacing the belts on a BioClip unitIMPORTANT IMFORMATION BioClipMAINTENANCE Service position for cutting unit Placing in service positionMAINTENANCE 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCEMAINTENANCE Restoring from service positionMAINTENANCE Checking the bladesBioClip103 BioClip Cutting units with rear ejection Cutting units with side ejectionMAINTENANCE Replacing the break-pin BioClipIMPORTANT INFORMATION LUBRICATIONCheck the engine’s oil level Changing the oilLUBRICATION Lubricating the belt adjusterCheck the transmission’s oil level General lubricationTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage Cutting unit TECHNICAL DATADimensions Electrical systemDirective 89/392/EEC, Annex II, A TECHNICAL DATA EU declaration of conformity Only applies to EuropeWork done SERVICEJOURNAL RIDERPre-delivery service After first 5 hoursEnglish SERVICEJOURNALWork done Date, mileage, stamp, sign46 - English SERVICEJOURNALWork done Date, mileage, stamp, signEnglish SERVICEJOURNALWork done Date, mileage, stamp, signDate, mileage, stamp, sign ´*3-G¶5O¨SERVICEJOURNAL Work donePage ´*3-G¶5O¨ 2001W03