Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 16 manual Restoring from service position, Maintenance

Models: Rider 16

1 51

Download 51 pages 44.5 Kb

Page 36

Image 36

MAINTENANCE

8.Lift off the drive belt (1). Then pull out the pin

(2).

Take care not to get your hand trapped.

9. Pull the frame forwards and refit the pin.

10.Grasp the front edge of the cutting unit, pull out and raise into the service position.

If the cylindrical bolt, which is now holding the cutting unit is removed, the cutting unit can be lifted off.

Restoring from service position

To leave the service position, reverse the procedures set out in “Placing in the service position”. Make sure that the cutting unit’s ”lug” enters the loop correctly on the underside of the machine, see diagram.

English – 35

Page 36

Image 36

Husqvarna Rider 16 manual Restoring from service position, Maintenance

Contents

101 RiderOperator´s manual CONTENTS Operator’s Manual for Rider IMPORTANT INFORMATIONSAFETY INSTRUCTIONS Safe operation practices for ride-on mowersI. General operation II. Slope operationIV. Service Danger, keep hands and feet awaySAFETY INSTRUCTIONS INSTRUCTION Dear customerTravel and transport on public roads TowingGood service Serial numberEngine TransmissionEXPLANATION OF SYMBOLS General use Read the instructions before starting the machinereversing Never carry passengersBe extra careful when driving on slopes Driving on slopesDo as follows Cut slopes upwards and downwards, not sidewaysMaintenance ChildrenKeep children away from the mowing area Never allow children to drive the machinebattery can explode and cause severe injuries Clean the machine regularly from grass, leaves and other wasteSAFETY INSTRUCTIONS Avoid overfilling. f fuel has been spilt on thePRESENTATION PresentationLocation of the controls obstruct the pedals when mowing Throttle and Choke leverSpeed limiter Parking brakeCutting unit Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionLever for adjustment of cutting height SeatFuelling PRESENTATIONDRIVING Starting the engineCold engine Warm engine DRIVING4. Set the throttle control midway between position 1 and IMPORTANT INFORMATIONDriving the machine DRIVINGCutting tips Mowing patternDRIVING IMPORTANT INFORMATIONStopping the engine Release leverDRIVING MAINTENANCE Maintenance scheduleMaintenance interval MaintenanceDismantling of the machine hoods Engine hoodFront hood Right-hand fenderChecking and adjustment of the steering wires Adjusting the brakePoorly adjusted brakes can result in reduced braking power MAINTENANCEChecking and adjustment of the throttle wire Replacement of the fuel filterMAINTENANCE Do not use compressed air to clean the paper filter Replacing the air filterMAINTENANCE IMPORTANT INFORMATIONCheck the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter MAINTENANCEInspecting the safety system MAINTENANCEChecking the tyre pressure Check the engine’s cooling air intakeMAINTENANCE IMPORTANT INFORMATIONInstalling BioClip Fitting the cutting unitMAINTENANCE Checking and adjustment of the cutting unit’s ground pressure Checking the cutting unit’s parallelismMAINTENANCE Adjusting the parallelism of the cutting unit Removing the cutting unitMAINTENANCE Wear gloves to protect your hands when working with the blades Replacing the cutting unit beltsReplacing the belts on a BioClip unit BioClip BioClip BioClipIMPORTANT IMFORMATION BioClipMAINTENANCE Service position for cutting unit Placing in service positionMAINTENANCE MAINTENANCE 5. Disengage the spring from the drive belt tensioning wheelRestoring from service position MAINTENANCEChecking the blades BioClip103 BioClip Cutting units with rear ejectionCutting units with side ejection MAINTENANCEReplacing the break-pin BioClip MAINTENANCELUBRICATION Check the engine’s oil levelChanging the oil IMPORTANT INFORMATIONLubricating the belt adjuster Check the transmission’s oil levelGeneral lubrication LUBRICATIONTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage TECHNICAL DATA DimensionsElectrical system Cutting unitTECHNICAL DATA EU declaration of conformity Only applies to Europe Directive 89/392/EEC, Annex II, ASERVICEJOURNAL RIDER Pre-delivery serviceAfter first 5 hours Work doneSERVICEJOURNAL Work doneDate, mileage, stamp, sign EnglishSERVICEJOURNAL Work doneDate, mileage, stamp, sign 46 - EnglishSERVICEJOURNAL Work doneDate, mileage, stamp, sign English´*3-G¶5O¨ SERVICEJOURNALWork done Date, mileage, stamp, signPage ´*3-G¶5O¨ 2001W03