Operator´s manual
101
Rider
CONTENTS Operator’s Manual for Rider
IMPORTANT INFORMATION
I. General operation
SAFETY INSTRUCTIONS
Safe operation practices for ride-on mowers
II. Slope operation
SAFETY INSTRUCTIONS
IV. Service
Danger, keep hands and feet away
Travel and transport on public roads
INSTRUCTION
Dear customer
Towing
Engine
Good service
Serial number
Transmission
EXPLANATION OF SYMBOLS
reversing
General use
Read the instructions before starting the machine
Never carry passengers
Do as follows
Be extra careful when driving on slopes
Driving on slopes
Cut slopes upwards and downwards, not sideways
Keep children away from the mowing area
Maintenance
Children
Never allow children to drive the machine
SAFETY INSTRUCTIONS
battery can explode and cause severe injuries
Clean the machine regularly from grass, leaves and other waste
Avoid overfilling. f fuel has been spilt on the
Location of the controls
PRESENTATION
Presentation
Speed limiter
obstruct the pedals when mowing
Throttle and Choke lever
Parking brake
Lifting of the cutting unit transport position
Cutting unit
Lift lever for cutting unit
Lowering of the cutting unit cutting position
Fuelling
Lever for adjustment of cutting height
Seat
PRESENTATION
Cold engine
DRIVING
Starting the engine
4. Set the throttle control midway between position 1 and
Warm engine
DRIVING
IMPORTANT INFORMATION
Driving the machine
DRIVING
DRIVING
Cutting tips
Mowing pattern
IMPORTANT INFORMATION
DRIVING
Stopping the engine
Release lever
Maintenance interval
MAINTENANCE
Maintenance schedule
Maintenance
Front hood
Dismantling of the machine hoods
Engine hood
Right-hand fender
Poorly adjusted brakes can result in reduced braking power
Checking and adjustment of the steering wires
Adjusting the brake
MAINTENANCE
MAINTENANCE
Checking and adjustment of the throttle wire
Replacement of the fuel filter
MAINTENANCE
Do not use compressed air to clean the paper filter
Replacing the air filter
IMPORTANT INFORMATION
Checking of the fuel pump’s air filter
Check the level of the battery acid
Procedures on contact with acid
MAINTENANCE
Inspecting the safety system
MAINTENANCE
MAINTENANCE
Checking the tyre pressure
Check the engine’s cooling air intake
IMPORTANT INFORMATION
MAINTENANCE
Installing BioClip
Fitting the cutting unit
MAINTENANCE
Checking and adjustment of the cutting unit’s ground pressure
Checking the cutting unit’s parallelism
MAINTENANCE
Adjusting the parallelism of the cutting unit
Removing the cutting unit
Replacing the belts on a BioClip unit
Wear gloves to protect your hands when working with the blades
Replacing the cutting unit belts
BioClip BioClip BioClip
MAINTENANCE
IMPORTANT IMFORMATION
BioClip
MAINTENANCE
Service position for cutting unit
Placing in service position
MAINTENANCE
5. Disengage the spring from the drive belt tensioning wheel
Restoring from service position
MAINTENANCE
Cutting units with side ejection
Checking the blades
BioClip103 BioClip Cutting units with rear ejection
MAINTENANCE
Replacing the break-pin BioClip
MAINTENANCE
Changing the oil
LUBRICATION
Check the engine’s oil level
IMPORTANT INFORMATION
General lubrication
Lubricating the belt adjuster
Check the transmission’s oil level
LUBRICATION
Procedure
TROUBLE SHOOTING SCHEDULE
Problem
Winter storage
Service
STORAGE
Electrical system
TECHNICAL DATA
Dimensions
Cutting unit
TECHNICAL DATA EU declaration of conformity Only applies to Europe
Directive 89/392/EEC, Annex II, A
After first 5 hours
SERVICEJOURNAL RIDER
Pre-delivery service
Work done
Date, mileage, stamp, sign
SERVICEJOURNAL
Work done
English
Date, mileage, stamp, sign
SERVICEJOURNAL
Work done
46 - English
Date, mileage, stamp, sign
SERVICEJOURNAL
Work done
English
Work done
´*3-G¶5O¨
SERVICEJOURNAL
Date, mileage, stamp, sign
Page
´*3-G¶5O¨ 2001W03