Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 16 manual Important Imformation, BioClip, Maintenance

Models: Rider 16

1 51

Download 51 pages 44.5 Kb

Page 33

IMPORTANT IMFORMATION

MAINTENANCE

IMPORTANT IMFORMATION

On a BioClip unit the blades are set at an angle of 90° to each other. If this angle changes, the blades may touch and cause damage to the cutting unit.

5.Fitting: First slide on the lower belt, then the upper belt.

Check that the blades appear as shown in the diagram, at an angle of 90° to each other. If not, adjust the belts. While the blade bearing is loose the belts can be slid onto the next tooth.

Tighten the nuts sufficiently so that the bearings are touching the cutting deck but can still be moved.

Tension the belts by turning the cam mechanism on top of the cutting deck. Tighten the nut.

Tighten all the nuts to secure the blade bearings.

6.The belt tension is correct when a force of 10 N pushes the belt in 7 mm.

Fit the safety cover over the belts and refit the lift strut.

Changing the belt on cutting units with side ejection or rear ejection

On cutting units with side ejection or rear ejection the blades are driven by a V-belt. This belt is replaced as follows:

1.Dismantling the cutting unit, see page 30.

2.Undo the bolt on the lift strut and the two screws on the cover. Lift the cover off the cutting unit.

3.Release the spring that tensions the V-belt and prise off the belt.

Replace the new belt by reversing the sequence.

BioClip 103

32 – English

Image 33

Husqvarna Rider 16 manual Important Imformation, BioClip, Maintenance

Contents

101 RiderOperator´s manual IMPORTANT INFORMATION CONTENTS Operator’s Manual for RiderSafe operation practices for ride-on mowers SAFETY INSTRUCTIONSI. General operation II. Slope operationIV. Service Danger, keep hands and feet awaySAFETY INSTRUCTIONS Dear customer INSTRUCTIONTravel and transport on public roads TowingSerial number Good serviceEngine TransmissionEXPLANATION OF SYMBOLS Read the instructions before starting the machine General usereversing Never carry passengersDriving on slopes Be extra careful when driving on slopesDo as follows Cut slopes upwards and downwards, not sidewaysChildren MaintenanceKeep children away from the mowing area Never allow children to drive the machineClean the machine regularly from grass, leaves and other waste battery can explode and cause severe injuriesSAFETY INSTRUCTIONS Avoid overfilling. f fuel has been spilt on thePRESENTATION PresentationLocation of the controls Throttle and Choke lever obstruct the pedals when mowingSpeed limiter Parking brakeLift lever for cutting unit Cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionSeat Lever for adjustment of cutting heightFuelling PRESENTATIONDRIVING Starting the engineCold engine DRIVING Warm engine4. Set the throttle control midway between position 1 and IMPORTANT INFORMATIONDRIVING Driving the machineMowing pattern Cutting tipsDRIVING IMPORTANT INFORMATIONStopping the engine Release leverDRIVING Maintenance schedule MAINTENANCEMaintenance interval MaintenanceEngine hood Dismantling of the machine hoodsFront hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power MAINTENANCEChecking and adjustment of the throttle wire Replacement of the fuel filterMAINTENANCE Replacing the air filter Do not use compressed air to clean the paper filterMAINTENANCE IMPORTANT INFORMATIONProcedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter MAINTENANCEMAINTENANCE Inspecting the safety systemCheck the engine’s cooling air intake Checking the tyre pressureMAINTENANCE IMPORTANT INFORMATIONInstalling BioClip Fitting the cutting unitMAINTENANCE Checking and adjustment of the cutting unit’s ground pressure Checking the cutting unit’s parallelismMAINTENANCE Adjusting the parallelism of the cutting unit Removing the cutting unitMAINTENANCE Replacing the cutting unit belts Wear gloves to protect your hands when working with the bladesReplacing the belts on a BioClip unit BioClip BioClip BioClipIMPORTANT IMFORMATION BioClipMAINTENANCE Service position for cutting unit Placing in service positionMAINTENANCE 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCEMAINTENANCE Restoring from service positionBioClip103 BioClip Cutting units with rear ejection Checking the bladesCutting units with side ejection MAINTENANCEMAINTENANCE Replacing the break-pin BioClipCheck the engine’s oil level LUBRICATIONChanging the oil IMPORTANT INFORMATIONCheck the transmission’s oil level Lubricating the belt adjusterGeneral lubrication LUBRICATIONTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage Dimensions TECHNICAL DATAElectrical system Cutting unitDirective 89/392/EEC, Annex II, A TECHNICAL DATA EU declaration of conformity Only applies to EuropePre-delivery service SERVICEJOURNAL RIDERAfter first 5 hours Work doneWork done SERVICEJOURNALDate, mileage, stamp, sign EnglishWork done SERVICEJOURNALDate, mileage, stamp, sign 46 - EnglishWork done SERVICEJOURNALDate, mileage, stamp, sign EnglishSERVICEJOURNAL ´*3-G¶5O¨Work done Date, mileage, stamp, signPage ´*3-G¶5O¨ 2001W03