Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 16 manual Maintenance, Disengage the spring from the drive belt tensioning wheel

Models: Rider 16

1 51

Download 51 pages 44.5 Kb

Page 35

Image 35

5.Disengage the spring from the drive belt tensioning wheel.

MAINTENANCE

4.Fit the support wheels on either side of the rear of the cutting unit.

WARNING!

Wear protective glasses when dismantling the cutting unit. The spring which tensions up the belt can go off and cause personal injury.

5.Disengage the spring from the drive belt tensioning wheel.

6.Move the cutting height lever to the lower position.

7.Place a foot on the front edge of the cutting unit near the wheel and raise the front edge of the unit to make it easier to remove the lift strut.

Engage the strut in the holder.

34 – English

Page 35

Image 35

Husqvarna Rider 16 manual Maintenance, Disengage the spring from the drive belt tensioning wheel

Contents

Operator´s manual 101Rider IMPORTANT INFORMATION CONTENTS Operator’s Manual for RiderII. Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers I. General operationSAFETY INSTRUCTIONS IV. ServiceDanger, keep hands and feet away Towing INSTRUCTIONDear customer Travel and transport on public roadsTransmission Good serviceSerial number EngineEXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine reversingCut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes Do as followsNever allow children to drive the machine MaintenanceChildren Keep children away from the mowing areaAvoid overfilling. f fuel has been spilt on the battery can explode and cause severe injuriesClean the machine regularly from grass, leaves and other waste SAFETY INSTRUCTIONSLocation of the controls PRESENTATIONPresentation Parking brake obstruct the pedals when mowingThrottle and Choke lever Speed limiterLowering of the cutting unit cutting position Cutting unitLift lever for cutting unit Lifting of the cutting unit transport positionPRESENTATION Lever for adjustment of cutting heightSeat FuellingCold engine DRIVINGStarting the engine IMPORTANT INFORMATION Warm engineDRIVING 4. Set the throttle control midway between position 1 andDRIVING Driving the machineIMPORTANT INFORMATION Cutting tipsMowing pattern DRIVINGDRIVING Stopping the engineRelease lever Maintenance MAINTENANCEMaintenance schedule Maintenance intervalRight-hand fender Dismantling of the machine hoodsEngine hood Front hoodMAINTENANCE Checking and adjustment of the steering wiresAdjusting the brake Poorly adjusted brakes can result in reduced braking powerMAINTENANCE Checking and adjustment of the throttle wireReplacement of the fuel filter IMPORTANT INFORMATION Do not use compressed air to clean the paper filterReplacing the air filter MAINTENANCEMAINTENANCE Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterMAINTENANCE Inspecting the safety systemIMPORTANT INFORMATION Checking the tyre pressureCheck the engine’s cooling air intake MAINTENANCEMAINTENANCE Installing BioClipFitting the cutting unit MAINTENANCE Checking and adjustment of the cutting unit’s ground pressureChecking the cutting unit’s parallelism MAINTENANCE Adjusting the parallelism of the cutting unitRemoving the cutting unit BioClip BioClip BioClip Wear gloves to protect your hands when working with the bladesReplacing the cutting unit belts Replacing the belts on a BioClip unitMAINTENANCE IMPORTANT IMFORMATIONBioClip MAINTENANCE Service position for cutting unitPlacing in service position 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCEMAINTENANCE Restoring from service positionMAINTENANCE Checking the bladesBioClip103 BioClip Cutting units with rear ejection Cutting units with side ejectionMAINTENANCE Replacing the break-pin BioClipIMPORTANT INFORMATION LUBRICATIONCheck the engine’s oil level Changing the oilLUBRICATION Lubricating the belt adjusterCheck the transmission’s oil level General lubricationProcedure TROUBLE SHOOTING SCHEDULEProblem Winter storage ServiceSTORAGE Cutting unit TECHNICAL DATADimensions Electrical systemDirective 89/392/EEC, Annex II, A TECHNICAL DATA EU declaration of conformity Only applies to EuropeWork done SERVICEJOURNAL RIDERPre-delivery service After first 5 hoursEnglish SERVICEJOURNALWork done Date, mileage, stamp, sign46 - English SERVICEJOURNALWork done Date, mileage, stamp, signEnglish SERVICEJOURNALWork done Date, mileage, stamp, signDate, mileage, stamp, sign ´*3-G¶5O¨SERVICEJOURNAL Work donePage ´*3-G¶5O¨ 2001W03