Rider
101
Operator´s manual
IMPORTANT INFORMATION
CONTENTS Operator’s Manual for Rider
Safe operation practices for ride-on mowers
SAFETY INSTRUCTIONS
I. General operation
II. Slope operation
Danger, keep hands and feet away
IV. Service
SAFETY INSTRUCTIONS
Dear customer
INSTRUCTION
Travel and transport on public roads
Towing
Serial number
Good service
Engine
Transmission
EXPLANATION OF SYMBOLS
Read the instructions before starting the machine
General use
reversing
Never carry passengers
Driving on slopes
Be extra careful when driving on slopes
Do as follows
Cut slopes upwards and downwards, not sideways
Children
Maintenance
Keep children away from the mowing area
Never allow children to drive the machine
Clean the machine regularly from grass, leaves and other waste
battery can explode and cause severe injuries
SAFETY INSTRUCTIONS
Avoid overfilling. f fuel has been spilt on the
Presentation
PRESENTATION
Location of the controls
Throttle and Choke lever
obstruct the pedals when mowing
Speed limiter
Parking brake
Lift lever for cutting unit
Cutting unit
Lifting of the cutting unit transport position
Lowering of the cutting unit cutting position
Seat
Lever for adjustment of cutting height
Fuelling
PRESENTATION
Starting the engine
DRIVING
Cold engine
DRIVING
Warm engine
4. Set the throttle control midway between position 1 and
IMPORTANT INFORMATION
DRIVING
Driving the machine
Mowing pattern
Cutting tips
DRIVING
IMPORTANT INFORMATION
Release lever
Stopping the engine
DRIVING
Maintenance schedule
MAINTENANCE
Maintenance interval
Maintenance
Engine hood
Dismantling of the machine hoods
Front hood
Right-hand fender
Adjusting the brake
Checking and adjustment of the steering wires
Poorly adjusted brakes can result in reduced braking power
MAINTENANCE
Replacement of the fuel filter
Checking and adjustment of the throttle wire
MAINTENANCE
Replacing the air filter
Do not use compressed air to clean the paper filter
MAINTENANCE
IMPORTANT INFORMATION
Procedures on contact with acid
Check the level of the battery acid
Checking of the fuel pump’s air filter
MAINTENANCE
MAINTENANCE
Inspecting the safety system
Check the engine’s cooling air intake
Checking the tyre pressure
MAINTENANCE
IMPORTANT INFORMATION
Fitting the cutting unit
Installing BioClip
MAINTENANCE
Checking the cutting unit’s parallelism
Checking and adjustment of the cutting unit’s ground pressure
MAINTENANCE
Removing the cutting unit
Adjusting the parallelism of the cutting unit
MAINTENANCE
Replacing the cutting unit belts
Wear gloves to protect your hands when working with the blades
Replacing the belts on a BioClip unit
BioClip BioClip BioClip
BioClip
IMPORTANT IMFORMATION
MAINTENANCE
Placing in service position
Service position for cutting unit
MAINTENANCE
5. Disengage the spring from the drive belt tensioning wheel
MAINTENANCE
MAINTENANCE
Restoring from service position
BioClip103 BioClip Cutting units with rear ejection
Checking the blades
Cutting units with side ejection
MAINTENANCE
MAINTENANCE
Replacing the break-pin BioClip
Check the engine’s oil level
LUBRICATION
Changing the oil
IMPORTANT INFORMATION
Check the transmission’s oil level
Lubricating the belt adjuster
General lubrication
LUBRICATION
Problem
TROUBLE SHOOTING SCHEDULE
Procedure
STORAGE
Service
Winter storage
Dimensions
TECHNICAL DATA
Electrical system
Cutting unit
Directive 89/392/EEC, Annex II, A
TECHNICAL DATA EU declaration of conformity Only applies to Europe
Pre-delivery service
SERVICEJOURNAL RIDER
After first 5 hours
Work done
Work done
SERVICEJOURNAL
Date, mileage, stamp, sign
English
Work done
SERVICEJOURNAL
Date, mileage, stamp, sign
46 - English
Work done
SERVICEJOURNAL
Date, mileage, stamp, sign
English
SERVICEJOURNAL
´*3-G¶5O¨
Work done
Date, mileage, stamp, sign
Page
´*3-G¶5O¨ 2001W03