Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 16 Dismantling of the machine hoods, Engine hood, Front hood, Right-hand fender

Models: Rider 16

1 51

Download 51 pages 44.5 Kb

Page 22

Image 22

MAINTENANCE

Dismantling of the machine hoods

Engine hood

The engine is accessible for servicing when the engine hood is lifted up.

Tilt the seat forward, release the rubber strap under the seat, and tilt the hood backwards.

Front hood

Release the clip on the front hood and lift off the fender.

Right-hand fender

Remove the knob (1), the screws (2 and 3) and lift off the hood.

Left-hand fender

Release the screws in the fender (2) and lift off the fender.

English – 21

Page 22

Image 22

Husqvarna Rider 16 manual Dismantling of the machine hoods, Engine hood, Front hood, Right-hand fender, Left-hand fender

Contents

Rider 101Operator´s manual CONTENTS Operator’s Manual for Rider IMPORTANT INFORMATIONI. General operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers II. Slope operationDanger, keep hands and feet away IV. ServiceSAFETY INSTRUCTIONS Travel and transport on public roads INSTRUCTIONDear customer TowingEngine Good serviceSerial number TransmissionEXPLANATION OF SYMBOLS reversing General useRead the instructions before starting the machine Never carry passengersDo as follows Be extra careful when driving on slopesDriving on slopes Cut slopes upwards and downwards, not sidewaysKeep children away from the mowing area MaintenanceChildren Never allow children to drive the machineSAFETY INSTRUCTIONS battery can explode and cause severe injuriesClean the machine regularly from grass, leaves and other waste Avoid overfilling. f fuel has been spilt on thePresentation PRESENTATIONLocation of the controls Speed limiter obstruct the pedals when mowingThrottle and Choke lever Parking brakeLifting of the cutting unit transport position Cutting unitLift lever for cutting unit Lowering of the cutting unit cutting positionFuelling Lever for adjustment of cutting heightSeat PRESENTATIONStarting the engine DRIVINGCold engine 4. Set the throttle control midway between position 1 and Warm engineDRIVING IMPORTANT INFORMATIONDriving the machine DRIVINGDRIVING Cutting tipsMowing pattern IMPORTANT INFORMATIONRelease lever Stopping the engineDRIVING Maintenance interval MAINTENANCEMaintenance schedule MaintenanceFront hood Dismantling of the machine hoodsEngine hood Right-hand fenderPoorly adjusted brakes can result in reduced braking power Checking and adjustment of the steering wiresAdjusting the brake MAINTENANCEReplacement of the fuel filter Checking and adjustment of the throttle wireMAINTENANCE MAINTENANCE Do not use compressed air to clean the paper filterReplacing the air filter IMPORTANT INFORMATIONChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid MAINTENANCEInspecting the safety system MAINTENANCEMAINTENANCE Checking the tyre pressureCheck the engine’s cooling air intake IMPORTANT INFORMATIONFitting the cutting unit Installing BioClipMAINTENANCE Checking the cutting unit’s parallelism Checking and adjustment of the cutting unit’s ground pressureMAINTENANCE Removing the cutting unit Adjusting the parallelism of the cutting unitMAINTENANCE Replacing the belts on a BioClip unit Wear gloves to protect your hands when working with the bladesReplacing the cutting unit belts BioClip BioClip BioClipBioClip IMPORTANT IMFORMATIONMAINTENANCE Placing in service position Service position for cutting unitMAINTENANCE MAINTENANCE 5. Disengage the spring from the drive belt tensioning wheelRestoring from service position MAINTENANCECutting units with side ejection Checking the bladesBioClip103 BioClip Cutting units with rear ejection MAINTENANCEReplacing the break-pin BioClip MAINTENANCEChanging the oil LUBRICATIONCheck the engine’s oil level IMPORTANT INFORMATIONGeneral lubrication Lubricating the belt adjusterCheck the transmission’s oil level LUBRICATIONProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage Electrical system TECHNICAL DATADimensions Cutting unitTECHNICAL DATA EU declaration of conformity Only applies to Europe Directive 89/392/EEC, Annex II, AAfter first 5 hours SERVICEJOURNAL RIDERPre-delivery service Work doneDate, mileage, stamp, sign SERVICEJOURNALWork done EnglishDate, mileage, stamp, sign SERVICEJOURNALWork done 46 - EnglishDate, mileage, stamp, sign SERVICEJOURNALWork done EnglishWork done ´*3-G¶5O¨SERVICEJOURNAL Date, mileage, stamp, signPage ´*3-G¶5O¨ 2001W03