Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 16 manual Checking the blades, BioClip103 BioClip Cutting units with rear ejection

Models: Rider 16

1 51

Download 51 pages 44.5 Kb

Page 37

Image 37

MAINTENANCE

Checking the blades

To achieve the best mowing results it is important that the blades are undamaged and well-sharpened.

Check that the blades’ attachment screws are tight.

IMPORTANT INFORMATION

Replacing or sharpening the blades should be conducted by an authorised service workshop.

The blades should be balanced after sharpening.

Damaged blades should be replaced when hitting obstacles that result in a breakdown. Let the servicing dealer judge whether the blade can be repaired/ground or must be discarded.

IMPORTANT INFORMATION

On the Bioclip unit the relative positioning of the blades should always be as shown in the diagram with an angle of 90° between the blades. Otherwise the blades can go against each other and damage the unit.

BioClip103

BioClip 90

Cutting units with rear ejection

Cutting units with side ejection

36 – English

Page 37

Image 37

Husqvarna Rider 16 manual Checking the blades, BioClip103 BioClip Cutting units with rear ejection, Maintenance

Contents

Rider 101Operator´s manual IMPORTANT INFORMATION CONTENTS Operator’s Manual for RiderSafe operation practices for ride-on mowers SAFETY INSTRUCTIONSI. General operation II. Slope operationDanger, keep hands and feet away IV. ServiceSAFETY INSTRUCTIONS Dear customer INSTRUCTIONTravel and transport on public roads TowingSerial number Good serviceEngine TransmissionEXPLANATION OF SYMBOLS Read the instructions before starting the machine General usereversing Never carry passengersDriving on slopes Be extra careful when driving on slopesDo as follows Cut slopes upwards and downwards, not sidewaysChildren MaintenanceKeep children away from the mowing area Never allow children to drive the machineClean the machine regularly from grass, leaves and other waste battery can explode and cause severe injuriesSAFETY INSTRUCTIONS Avoid overfilling. f fuel has been spilt on thePresentation PRESENTATIONLocation of the controls Throttle and Choke lever obstruct the pedals when mowingSpeed limiter Parking brakeLift lever for cutting unit Cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionSeat Lever for adjustment of cutting heightFuelling PRESENTATIONStarting the engine DRIVINGCold engine DRIVING Warm engine4. Set the throttle control midway between position 1 and IMPORTANT INFORMATIONDRIVING Driving the machineMowing pattern Cutting tipsDRIVING IMPORTANT INFORMATIONRelease lever Stopping the engineDRIVING Maintenance schedule MAINTENANCEMaintenance interval MaintenanceEngine hood Dismantling of the machine hoodsFront hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power MAINTENANCEReplacement of the fuel filter Checking and adjustment of the throttle wireMAINTENANCE Replacing the air filter Do not use compressed air to clean the paper filterMAINTENANCE IMPORTANT INFORMATIONProcedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter MAINTENANCEMAINTENANCE Inspecting the safety systemCheck the engine’s cooling air intake Checking the tyre pressureMAINTENANCE IMPORTANT INFORMATIONFitting the cutting unit Installing BioClipMAINTENANCE Checking the cutting unit’s parallelism Checking and adjustment of the cutting unit’s ground pressureMAINTENANCE Removing the cutting unit Adjusting the parallelism of the cutting unitMAINTENANCE Replacing the cutting unit belts Wear gloves to protect your hands when working with the bladesReplacing the belts on a BioClip unit BioClip BioClip BioClipBioClip IMPORTANT IMFORMATIONMAINTENANCE Placing in service position Service position for cutting unitMAINTENANCE 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCEMAINTENANCE Restoring from service positionBioClip103 BioClip Cutting units with rear ejection Checking the bladesCutting units with side ejection MAINTENANCEMAINTENANCE Replacing the break-pin BioClipCheck the engine’s oil level LUBRICATIONChanging the oil IMPORTANT INFORMATIONCheck the transmission’s oil level Lubricating the belt adjusterGeneral lubrication LUBRICATIONProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage Dimensions TECHNICAL DATAElectrical system Cutting unitDirective 89/392/EEC, Annex II, A TECHNICAL DATA EU declaration of conformity Only applies to EuropePre-delivery service SERVICEJOURNAL RIDERAfter first 5 hours Work doneWork done SERVICEJOURNALDate, mileage, stamp, sign EnglishWork done SERVICEJOURNALDate, mileage, stamp, sign 46 - EnglishWork done SERVICEJOURNALDate, mileage, stamp, sign EnglishSERVICEJOURNAL ´*3-G¶5O¨Work done Date, mileage, stamp, signPage ´*3-G¶5O¨ 2001W03