Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Rider 16 Checking the tyre pressure, Check the engine’s cooling air intake, Maintenance

Models: Rider 16

1 51

Download 51 pages 44.5 Kb

Page 28

Image 28

MAINTENANCE

Checking the tyre pressure

The tyre pressure should be 60 kPa (0.6 kp/cm2) all round.

To improve driving the pressure on the rear tyres can be reduced to 40 kPa (0.4 kp/cm2).

The maximum tyre pressure is 100 kPa (1.0 kp/cm2).

IMPORTANT INFORMATION

Different tyre pressures on the front tyres will result in the blades cutting the grass at different heights.

Check the engine’s cooling air intake

Fold open the engine cover as described on page 21.

Check that the cooling intake is free from leaves, grass and dirt.

If the cooling intake is blocked this will interfere with the cooling of the engine, which can damage the engine.

English – 27

Page 28

Image 28

Husqvarna Rider 16 Checking the tyre pressure, Check the engine’s cooling air intake, Maintenance, Important Information

Contents

Rider 101Operator´s manual CONTENTS Operator’s Manual for Rider IMPORTANT INFORMATIONSAFETY INSTRUCTIONS Safe operation practices for ride-on mowersI. General operation II. Slope operationDanger, keep hands and feet away IV. ServiceSAFETY INSTRUCTIONS INSTRUCTION Dear customerTravel and transport on public roads TowingGood service Serial numberEngine TransmissionEXPLANATION OF SYMBOLS General use Read the instructions before starting the machinereversing Never carry passengersBe extra careful when driving on slopes Driving on slopesDo as follows Cut slopes upwards and downwards, not sidewaysMaintenance ChildrenKeep children away from the mowing area Never allow children to drive the machinebattery can explode and cause severe injuries Clean the machine regularly from grass, leaves and other wasteSAFETY INSTRUCTIONS Avoid overfilling. f fuel has been spilt on thePresentation PRESENTATIONLocation of the controls obstruct the pedals when mowing Throttle and Choke leverSpeed limiter Parking brakeCutting unit Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionLever for adjustment of cutting height SeatFuelling PRESENTATIONStarting the engine DRIVINGCold engine Warm engine DRIVING4. Set the throttle control midway between position 1 and IMPORTANT INFORMATIONDriving the machine DRIVINGCutting tips Mowing patternDRIVING IMPORTANT INFORMATIONRelease lever Stopping the engineDRIVING MAINTENANCE Maintenance scheduleMaintenance interval MaintenanceDismantling of the machine hoods Engine hoodFront hood Right-hand fenderChecking and adjustment of the steering wires Adjusting the brakePoorly adjusted brakes can result in reduced braking power MAINTENANCEReplacement of the fuel filter Checking and adjustment of the throttle wireMAINTENANCE Do not use compressed air to clean the paper filter Replacing the air filterMAINTENANCE IMPORTANT INFORMATIONCheck the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter MAINTENANCEInspecting the safety system MAINTENANCEChecking the tyre pressure Check the engine’s cooling air intakeMAINTENANCE IMPORTANT INFORMATIONFitting the cutting unit Installing BioClipMAINTENANCE Checking the cutting unit’s parallelism Checking and adjustment of the cutting unit’s ground pressureMAINTENANCE Removing the cutting unit Adjusting the parallelism of the cutting unitMAINTENANCE Wear gloves to protect your hands when working with the blades Replacing the cutting unit beltsReplacing the belts on a BioClip unit BioClip BioClip BioClipBioClip IMPORTANT IMFORMATIONMAINTENANCE Placing in service position Service position for cutting unitMAINTENANCE MAINTENANCE 5. Disengage the spring from the drive belt tensioning wheelRestoring from service position MAINTENANCEChecking the blades BioClip103 BioClip Cutting units with rear ejectionCutting units with side ejection MAINTENANCEReplacing the break-pin BioClip MAINTENANCELUBRICATION Check the engine’s oil levelChanging the oil IMPORTANT INFORMATIONLubricating the belt adjuster Check the transmission’s oil levelGeneral lubrication LUBRICATIONProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage TECHNICAL DATA DimensionsElectrical system Cutting unitTECHNICAL DATA EU declaration of conformity Only applies to Europe Directive 89/392/EEC, Annex II, ASERVICEJOURNAL RIDER Pre-delivery serviceAfter first 5 hours Work doneSERVICEJOURNAL Work doneDate, mileage, stamp, sign EnglishSERVICEJOURNAL Work doneDate, mileage, stamp, sign 46 - EnglishSERVICEJOURNAL Work doneDate, mileage, stamp, sign English´*3-G¶5O¨ SERVICEJOURNALWork done Date, mileage, stamp, signPage ´*3-G¶5O¨ 2001W03