Rider
101
Operator´s manual
IMPORTANT INFORMATION
CONTENTS Operator’s Manual for Rider
II. Slope operation
SAFETY INSTRUCTIONS
Safe operation practices for ride-on mowers
I. General operation
Danger, keep hands and feet away
IV. Service
SAFETY INSTRUCTIONS
Towing
INSTRUCTION
Dear customer
Travel and transport on public roads
Transmission
Good service
Serial number
Engine
EXPLANATION OF SYMBOLS
Never carry passengers
General use
Read the instructions before starting the machine
reversing
Cut slopes upwards and downwards, not sideways
Be extra careful when driving on slopes
Driving on slopes
Do as follows
Never allow children to drive the machine
Maintenance
Children
Keep children away from the mowing area
Avoid overfilling. f fuel has been spilt on the
battery can explode and cause severe injuries
Clean the machine regularly from grass, leaves and other waste
SAFETY INSTRUCTIONS
Presentation
PRESENTATION
Location of the controls
Parking brake
obstruct the pedals when mowing
Throttle and Choke lever
Speed limiter
Lowering of the cutting unit cutting position
Cutting unit
Lift lever for cutting unit
Lifting of the cutting unit transport position
PRESENTATION
Lever for adjustment of cutting height
Seat
Fuelling
Starting the engine
DRIVING
Cold engine
IMPORTANT INFORMATION
Warm engine
DRIVING
4. Set the throttle control midway between position 1 and
DRIVING
Driving the machine
IMPORTANT INFORMATION
Cutting tips
Mowing pattern
DRIVING
Release lever
Stopping the engine
DRIVING
Maintenance
MAINTENANCE
Maintenance schedule
Maintenance interval
Right-hand fender
Dismantling of the machine hoods
Engine hood
Front hood
MAINTENANCE
Checking and adjustment of the steering wires
Adjusting the brake
Poorly adjusted brakes can result in reduced braking power
Replacement of the fuel filter
Checking and adjustment of the throttle wire
MAINTENANCE
IMPORTANT INFORMATION
Do not use compressed air to clean the paper filter
Replacing the air filter
MAINTENANCE
MAINTENANCE
Check the level of the battery acid
Procedures on contact with acid
Checking of the fuel pump’s air filter
MAINTENANCE
Inspecting the safety system
IMPORTANT INFORMATION
Checking the tyre pressure
Check the engine’s cooling air intake
MAINTENANCE
Fitting the cutting unit
Installing BioClip
MAINTENANCE
Checking the cutting unit’s parallelism
Checking and adjustment of the cutting unit’s ground pressure
MAINTENANCE
Removing the cutting unit
Adjusting the parallelism of the cutting unit
MAINTENANCE
BioClip BioClip BioClip
Wear gloves to protect your hands when working with the blades
Replacing the cutting unit belts
Replacing the belts on a BioClip unit
BioClip
IMPORTANT IMFORMATION
MAINTENANCE
Placing in service position
Service position for cutting unit
MAINTENANCE
5. Disengage the spring from the drive belt tensioning wheel
MAINTENANCE
MAINTENANCE
Restoring from service position
MAINTENANCE
Checking the blades
BioClip103 BioClip Cutting units with rear ejection
Cutting units with side ejection
MAINTENANCE
Replacing the break-pin BioClip
IMPORTANT INFORMATION
LUBRICATION
Check the engine’s oil level
Changing the oil
LUBRICATION
Lubricating the belt adjuster
Check the transmission’s oil level
General lubrication
Problem
TROUBLE SHOOTING SCHEDULE
Procedure
STORAGE
Service
Winter storage
Cutting unit
TECHNICAL DATA
Dimensions
Electrical system
Directive 89/392/EEC, Annex II, A
TECHNICAL DATA EU declaration of conformity Only applies to Europe
Work done
SERVICEJOURNAL RIDER
Pre-delivery service
After first 5 hours
English
SERVICEJOURNAL
Work done
Date, mileage, stamp, sign
46 - English
SERVICEJOURNAL
Work done
Date, mileage, stamp, sign
English
SERVICEJOURNAL
Work done
Date, mileage, stamp, sign
Date, mileage, stamp, sign
´*3-G¶5O¨
SERVICEJOURNAL
Work done
Page
´*3-G¶5O¨ 2001W03