Integra DTR-5.3 instruction manual Connecting a television monitor or projector Monitor OUT

Connections (DTR-6.3)

Video output

S Video output

Video input

S Video input

7.DVD recorder, other digital video recording device (VIDEO 2)

L (white)

Analog audio input R (red)

L (white)

Analog audio output R (red)

8. TV monitor or projector

(MONITOR OUT)

ANTENNA

FM 75

AM

R

PHONO IN

L

GND

COMPONENT VIDEO

INPUT 2 INPUT 1

OUTPUT

Y

12 V

RS232

Y

ZONE 2

TRIGGER

OUT

IR OUT

ZONE 2

DC IN

LINE OUT

56K

40K

PB

A

A

OUT

24V 1A

L

PB

B

B

R

PR

CONTRO

PR

Component video

REMOT

ZONE 2

VIDEO 1

input

DIGITAL INPUT

DIGITAL

VIDEO 3

VIDEO 2

DVD

MONITOR

IR

OUTPUT COAXIAL

IN

OUT

IN

OUT

IN

IN

OUT

OPTICAL

OPTICAL

V

OU

2

1

I

Video input

S

COAXIAL

DIGITAL

INPUT

IN	OUT	IN	IN	OUT	IN	OUT	IN FRONT SURR	CENTER
L							L	S Video input
SUBWOOFER
PRE OUT
R							R
								SUB
CD	TAPE		VIDEO 3	VIDEO 2		VIDEO 1
								WOOFER

DVD

: Signal flow

7.Connecting a DVD recorder or other digital video recording device (VIDEO 2)

Using RCA video cables, connect the video output jack (composite) of the device to the VIDEO 2 VIDEO IN jack of the DTR-6.3 and connect the video input jack of the device to the VIDEO 2 VIDEO OUT jack of the DTR-6.3. Or if the device has S video input and output jacks, using S video cables, connect the S video output jack of the device to the VIDEO 2 S VIDEO IN jack of the DTR-6.3 and connect the video input jack of the device to the VIDEO 2 S VIDEO OUT jack of the DTR-6.3. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the DTR-6.3.

With the initial settings of the DTR-6.3, the VIDEO 2 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using RCA audio cables, connect the audio output jacks of the device to the VIDEO 2 IN audio jacks of the DTR-6.3 and connect the audio input jacks of the device to the VIDEO 2 OUT audio jacks of the DTR-6.3. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the DTR-6.3 depending on the type of connector on the device.

With the initial settings of the DTR-6.3, nothing is allocated as the digital input source for VIDEO 2 (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page 53).

If the device has a digital input, connect it to the DIGITAL OUTPUT (OPTICAL or COAXIAL) jack of the DTR-6.3 for digital recording of the signal from the digital input of the DTR-6.3.

Note:

The output from the DIGITAL OUTPUT jack of the DTR-6.3 is only the digital signal input to the DIGITAL INPUT jack.

8.Connecting a television monitor or projector (MONITOR OUT)

The DTR-6.3 is equipped with a simple Y/C separate circuit and simple Y/C mixed circuit. Since both the signal from the S VIDEO and VIDEO inputs are output to the MONITOR OUT S VIDEO output, if the television or projector is equipped with an S video input, it is unnecessary to connect the video connectors. If it is equipped with only a video input, connect it to the MONITOR OUT VIDEO output.

Using an RCA video cable, connect the video input jack (composite) of the device to the MONITOR OUT VIDEO jack of the DTR-6.3. Or if the device has an S video input jack, connect it to the MONITOR OUT S VIDEO jack of the DTR-6.3 using an S video cable. Or if the device has component video inputs, connect them to the bank of COMPONENT VIDEO OUTPUT jacks on the DTR-6.3.

Note:

Note that the Setup Menu will only be displayed on the monitor connected to MONITOR OUT and not those connected to the COMPONENT VIDEO OUTPUT jacks.

20