Integra DTR-5.3 instruction manual Connecting a video cassette recorder Video

Connections (DTR-6.3)

: Signal flow	Y
	PB	Component video output
	PR

Video output

ANTENNA

FM 75

AM

R

PHONO IN

GND

6. Satellite tuner or television

L

COMPONENT VIDEO

S video output

(VIDEO 3)

INPUT 2

INPUT 1

OUTPUT

12 V

RS232

Y

ZONE 2

TRIGGER

OUT

IR OUT

ZONE 2

DC IN

LINE OUT

56K

40K

A

A

OUT

24V 1A

L

PB

B

REMOT

5. VCR (VIDEO 1)

B

R

CONTRO

PR

ZONE 2

VIDEO 1

DIGITAL INPUT

DIGITAL

VIDEO 3

VIDEO 2

DVD

MONITOR

IR

OUTPUT COAXIAL

IN

OUT

IN

OUT

IN

IN

OUT

Digital audio output

OPTICAL

OPTICAL

OU

V

2

1

(optical)

I

S

COAXIAL

DIGITAL

Video input

INPUT

IN

OUT

IN

IN

OUT

IN

OUT

IN

FRONT

SURR

CENTER

L

L

SUBWOOFER

PRE OUT

Video output

R

R

S video input

SUB

CD

TAPE

VIDEO 3

VIDEO 2

VIDEO 1

DVD

WOOFER

L (white)

S Video output

Analog audio output

L (white)

R (red)

L (white)

Analog audio output

R (red)

Analog audio input

R (red)

5. Connecting a video cassette recorder (VIDEO 1)

Using RCA video cables, connect the video output jack (composite) of the video cassette recorder to the VIDEO 1 VIDEO IN jack of the DTR-6.3 and connect the video input jack of the video cassette recorder to the VIDEO 1 VIDEO OUT jack of the DTR-6.3. Or if the video cassette recorder has S video input and output jacks, using S video cables, connect the S video output jack of the video cassette recorder to the VIDEO 1 S VIDEO IN jack of the DTR-6.3 and connect the video input jack of the video cassette recorder to the VIDEO 1 S VIDEO OUT jack of the DTR-6.3. Or if the video cassette recorder has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the DTR-6.3.

With the initial settings of the DTR-6.3, the VIDEO 1 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the video cassette recorder to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using RCA audio cables, connect the audio output jacks of the video cassette recorder to the VIDEO 1 IN audio jacks of the DTR-6.3 and connect the audio input jacks of the video cassette recorder to the VIDEO 1 OUT audio jacks of the DTR-6.3. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

With the initial settings of the DTR-6.3, nothing is allocated as the digital input source for VIDEO 1 (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page 53).

6.Connecting a satellite tuner, television, or settop box (VIDEO 3)

Using an RCA video cable, connect the video output jack (composite) of the device to the VIDEO 3 VIDEO IN jack of the DTR-6.3. Or if the device has an S video output jack, connect it to the VIDEO 3 S VIDEO IN jack of the DTR-6.3 using an S video cable. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the DTR-6.3.

With the initial settings of the DTR-6.3, the VIDEO 3 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using an RCA audio cable, connect the audio output jack of the device to the VIDEO 3 IN audio jacks of the DTR-6.3. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the DTR-6.3 depending on the type of connector on the device.

With the initial settings of the DTR-6.3, the VIDEO 3 input source is set for digital input at the OPTICAL 2 jack (OPT 2).

If the digital connection is made at a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 53).

19