Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 manual Configuring the SNMP agent for IP, To configure a port for full duplex

Models: 654655-001

1 83

Download 83 pages 573 b

Page 24

C H A P T E R 2 Intel Express 100BASE-TX Switching Hub

NOTE

You must have a point-to- point connection to establish a full-duplex connection (shared hubs/repeaters/ concentrators aren’t capable of full duplex). Additionally, both points of the connection must be configured for full duplex.

To configure a port for full duplex

1Configure the adapter or switch port on the other end for full duplex.

2Set the Express Switching Hub port to full duplex. This example sets port 3 to full duplex:

set-port-dplex 3 full

3Check the FC/FD LED. It should be solid yellow, indicating full duplex.

Configuring the SNMP agent for IP

Commands used

set-ip-conf

ping

Sets IP address, netmask, and broadcast address.

Contacts another IP device.

The switch can be monitored and controlled through any SNMP- compliant network management system (NMS). First, you must configure the SNMP agent by assigning an IP address.

To configure the SNMP agent

1Set the IP configuration. Type the command:

set-ip-conf 192.1.1.64 255.255.255.0 192.1.1.255

If the switch doesn’t have an IP address, then the specified IP configuration is changed immediately and saved in NVRAM.

If the switch is already configured, the command changes only the NVRAM. To use the new parameters, reset the switch using the warm-resetcommand.

2Test the installation. Type the command:

SYS_console> ping 192.1.1.1 2

This example tests connectivity from the switch to a workstation with an IP address of 192.1.1.1. For more information on the ping command, see page 33.

3Download the MIB from Intel’s Customer Support World Wide Web site (http://www-cs.intel.com). The file is compressed in the file SWCH1MIB.EXE.

4Compile the MIB into your NMS. See your NMS documentation for more information.

20

Image 24

Intel 654655-001 manual Configuring the SNMP agent for IP, To configure a port for full duplex, Commands used

Contents

Intel Express 100BASE-TXSwitching Hub User GuideFirst edition Contents Hardware Installation and Network TopologyConfiguring and Managing the Switch Quick StartTroubleshooting ChapterAppendix A Technical InformationQuick Start Console MgmtOptional Quick Start for SNMP Management Hardware Installation and NetworkTopology OverviewFeatures Installation and Setup 1 Install the switch in a rack or on a shelf2 Plug the switch in and turn the power on 4 Is setup complete?Using the Switch Port status LEDsManagement status LEDs Console MgmtCabling Requirements UTP requirementsFiber optic requirements Connector pinouts Straight-throughvs. crossover cablesDetermining which cable to use Typical Configurations Configuring the 100 Mbps workgroup environment100 Mbps clients using 100 Mbps clients usingConfiguring the Wide Area Network WAN environment or Switch ofSwitches BackboneConnecting to a 10 Mbps segment Switching HubServer equipped with two adapters, one atExcessive flow control problems Repeater count limitationsBy default, flow control is enabled on all ports Page Configuring and Managing the SwitchAccessing the Console Manager Accessing the Console Manager remotelyConsole Mgmt Using the Console Manager Entering commandscP at the prompt Console Manager command groups Configuring a port for full duplexCommands used Configuring the SNMP agent for IP To configure a port for full duplexCommands used To configure the SNMP agentMonitoring traffic Commands usedTo check traffic on a port Creating VLANs To create an SVLAN To create a VBDConfiguring the spanning tree Creating custom filtersConsole Command Reference To set a custom filterlogin help-kbdbanner clearSystem commands logoutset-prompt set-passwdwarm-reset cold-resetsys-stat get-last-err init-nvramset-line-slip set-sw-fileIP commands set-par-fileset-fg-param start-fgIP Configuration get-ipget-ip-conf set-ipget-bootp set-bootpset-ip-conf get-slipC H A P T E R Address Resolution Protocol ARP Commands ping-stopget-arp-tbl SNMP commands SNMP community stringsSNMP trap message commands set-commget-auth set-authSwitching database commands add-trapdel-trap The entry has these properties Configuring and Managing the Switch get-lt-16C H A P T E R find-lt-addr del-lt-entrydel-lt-addr add-lt-entry get-lt-ageset-lt-age Custom filtering get-lt-filteradd-cf-entry del-cf-entry get-nv-cftblget-nv-cfilt C H A P T E RVLAN commands get-con-matrixget-vbc-matrix set-vbc-domain del-vbc-domainget-vbc-tbl set-sec-vlanSpanning tree commands del-sec-vlanget-svlan-tbl set-mon-portget-stp set-stpget-st-bcfg get-st-pcfgset-br-hellot set-br-fwdelset-prt-prio set-prt-enbPort configuration commands get-port-cfgset-port-dplex Switching statistics commands set-port-fctrlclr-cnt get-eth-cntget-colls-cnt get-rmon-cntC H A P T E R packets or bytes received packets forwarded Configuring and Managing the Switch get-mgm-brcntC H A P T E R Console command-linesummary Console CommandsSystem Commands IP CommandsIP Commands con’t SNMP CommandsSwitching Database Commands Virtual LAN VLAN Commands Spanning Tree CommandsPort Configuration Commands Switching Statistics Commands C H A P T E RPage 3 Troubleshooting message Default Configuration A Technical InformationSpecifications FeaturesPorts Console ManagerStatus Indicators per port General IndicatorsBoot and Configuration Connector Interfaces115 volt configuration 230 volt configurationElectrical Specifications Power Cord SpecificationsSNMP and MIB Support Custom Filter Port Table Source PortsSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 Limited Warranty FCC NoticeManufacturer declaration A p p e n dPage I Index Page Page Page Page Page World Wide Web CompuServeIntel BBS FaxBack