Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 Configuring the Wide Area Network WAN environment, Backbone, Router, Bridge

Models: 654655-001

1 83

Download 83 pages 573 b

Page 15

Configuring the Wide Area Network (WAN) environment

C H A P T E R 1 Hardware Installation and Network Topology

Configuring the Wide Area Network (WAN) environment

Connections to the backbone are most effective using fiber optic cabling. This eliminates the 100 meter UTP restriction. Also, connect multiple switches directly to the backbone (not each other) and connect busy servers directly to the switch.

	Backbone	To T1 line
	Router, Bridge,	To T1 line
	Router, Bridge,
	or Switch of	To 10 Mbps segment
	Switches

		To dissimilar LANs
Port 1	Port 2	Intel Express
		Intel Express
		100BASE-TX Switching Hub

Port 3	Port 4	Port 5		Port 6	Port 7
					Console Mgmt	SNMP Pwr
MDI	MDI	MDI	MDI	MDI		Mgmt Fault
		100BASE-TX

➊

➋

Media Adapter	2	3	4	Intel Express
				Intel Express
				100BASE-T4 Stackable Hub
1				100 BASE-T4
				Expansion Slot

➌

						Media Adapter	2	3	4	Intel Express
										100BASE-T4 Stackable Hub
						1				100 BASE-T4
	Port 1			Port 2	Intel Express
					100BASE-TX Switching Hub					Expansion Slot
Port 3	Port 4	Port 5	Port 6		Port 7
					Console Mgmt	SNMP Pwr

MDI	MDI	MDI		MDI	MDI	Mgmt Fault
			100BASE-TX

Intel Express 100BASE-TX Stackable Hubs

➍

High speed 100 Mbps servers

Media Adapter	2	3	4	Intel Express
				100BASE-T4 Stackable Hub
1				100 BASE-T4
				Expansion Slot

Media Adapter	2	3	4	Intel Express
				Intel Express
				100BASE-T4 Stackable Hub
1				100 BASE-T4
				Expansion Slot

CAT5 UTP (100 meters max.) Multimode fiber (412 meters max. at half duplex, 2 Km max. at full duplex)

NOTES

➊100BASE-FX Fiber optic media adapter optional (product code ESMODFX).

➋You can also use CAT5 UTP to connect to a backbone router or bridge.

➌Configure high-speed servers for full duplex to achieve 200 Mbps throughput.

➍If a server isn’t accessed by more than one segment, move it to a hub on the segment.

PC-3438

11

Image 15

Intel 654655-001 manual Configuring the Wide Area Network WAN environment, Backbone, Router, Bridge, or Switch of, Switches

Contents

User Guide Intel Express 100BASE-TXSwitching HubFirst edition Quick Start ContentsHardware Installation and Network Topology Configuring and Managing the SwitchTechnical Information TroubleshootingChapter Appendix AConsole Mgmt Quick StartOptional Quick Start for SNMP Management Overview Hardware Installationand Network TopologyFeatures 4 Is setup complete? Installation and Setup1 Install the switch in a rack or on a shelf 2 Plug the switch in and turn the power onPort status LEDs Using the SwitchConsole Mgmt Management status LEDsCabling Requirements UTP requirementsFiber optic requirements Connector pinouts Straight-throughvs. crossover cablesDetermining which cable to use 100 Mbps clients using Typical ConfigurationsConfiguring the 100 Mbps workgroup environment 100 Mbps clients usingBackbone Configuring the Wide Area Network WAN environmentor Switch of Switchesadapters, one at Connecting to a 10 Mbps segmentSwitching Hub Server equipped with twoExcessive flow control problems Repeater count limitationsBy default, flow control is enabled on all ports Page Managing the Switch Configuring andAccessing the Console Manager Accessing the Console Manager remotelyConsole Mgmt Entering commands Using the Console ManagercP at the prompt Console Manager command groups Configuring a port for full duplexCommands used To configure the SNMP agent Configuring the SNMP agent for IPTo configure a port for full duplex Commands usedMonitoring traffic Commands usedTo check traffic on a port Creating VLANs To create a VBD To create an SVLANCreating custom filters Configuring the spanning treeTo set a custom filter Console Command Referenceclear loginhelp-kbd bannerset-passwd System commandslogout set-promptwarm-reset cold-resetsys-stat set-sw-file get-last-errinit-nvram set-line-slipstart-fg IP commandsset-par-file set-fg-paramset-ip IP Configurationget-ip get-ip-confget-slip get-bootpset-bootp set-ip-confC H A P T E R Address Resolution Protocol ARP Commands ping-stopget-arp-tbl SNMP community strings SNMP commandsset-auth SNMP trap message commandsset-comm get-authSwitching database commands add-trapdel-trap The entry has these properties Configuring and Managing the Switch get-lt-16C H A P T E R find-lt-addr del-lt-entrydel-lt-addr add-lt-entry get-lt-ageset-lt-age Custom filtering get-lt-filteradd-cf-entry C H A P T E R del-cf-entryget-nv-cftbl get-nv-cfiltVLAN commands get-con-matrixget-vbc-matrix set-sec-vlan set-vbc-domaindel-vbc-domain get-vbc-tblset-mon-port Spanning tree commandsdel-sec-vlan get-svlan-tblget-st-pcfg get-stpset-stp get-st-bcfgset-prt-enb set-br-hellotset-br-fwdel set-prt-prioPort configuration commands get-port-cfgset-port-dplex get-eth-cnt Switching statistics commandsset-port-fctrl clr-cntget-colls-cnt get-rmon-cntC H A P T E R packets or bytes received packets forwarded Configuring and Managing the Switch get-mgm-brcntC H A P T E R IP Commands Console command-linesummaryConsole Commands System CommandsIP Commands con’t SNMP CommandsSwitching Database Commands Virtual LAN VLAN Commands Spanning Tree CommandsPort Configuration Commands C H A P T E R Switching Statistics CommandsPage 3 Troubleshooting message A Technical Information Default ConfigurationConsole Manager SpecificationsFeatures PortsConnector Interfaces Status Indicators per portGeneral Indicators Boot and ConfigurationPower Cord Specifications 115 volt configuration230 volt configuration Electrical SpecificationsSNMP and MIB Support Source Ports Custom Filter Port TableSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 A p p e n d Limited WarrantyFCC Notice Manufacturer declarationPage I Index Page Page Page Page Page FaxBack World Wide WebCompuServe Intel BBS