Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 manual SNMP and MIB Support

Models: 654655-001

1 83

Download 83 pages 573 b

Page 69

A p p e n d i x

A

Technical Information

SNMP and MIB Support

The Express Switching Hub contains a built-in SNMP agent running on the SNMP processor board. This allows each Express Switching Hub to be managed from a centralized management station via any SNMP-compliant NMS.

The SNMP agent software complies with the following standards:

•RFC 1155, The Structure of Management Information (SMI) for TCP/IP Based Internets, 5/90.

•RFC 1556, Management Information Base (MIB) for Network Managers of TCP/IP Based Internets, 5/90.

•RFC 1557, The Simple Network Management Protocol (SNMP), 5/ 90.

•RFC 1213, The Management Information Base II (MIB II), 3/91.

•RFC 1643, Definitions of Managed Objects for the Ethernet-like Interface Types.

•RFC 1573, Evolution of the Interfaces Group of MIB-II, 1/94.

•RFC 1493, Definitions of Managed Objects for Bridges, 7/93.

•RFC 793, Transmission Control Protocol.

•RFC 854, Telnet Protocol Specification.

•RFC 1055, Nonstandard for transmission of IP datagrams over serial lines: SLIP, 1/88.

The SNMP agent uses UDP/IP (RFC 768, RFC 950, RFC 1071 and RFC 791) as OSI layers 3 and 4 protocols, and ICMP (RFC 792) and ARP (RFC 826) to complete the UDP/IP protocol suite.

The UDP/IP stack implementation is conformant to:

•RFC 1122, Requirements for Internet hosts, communication layers.

•RFC 1123, Requirements for Internet hosts, application and support.

The Express Switching Hub may be managed by any SNMP Manager that conforms to the above standards.

The Express Switching Hub implements an Intel Enterprise MIB. Download SWCH1MIB.EXE from the Intel Customer Support World Wide Web site (http://www-cs.intel.com) or Intel’s FTP site (see inside back cover).

65

Image 69

Intel 654655-001 manual SNMP and MIB Support

Contents

User Guide Intel Express 100BASE-TXSwitching HubFirst edition Hardware Installation and Network Topology ContentsConfiguring and Managing the Switch Quick StartChapter TroubleshootingAppendix A Technical InformationConsole Mgmt Quick StartOptional Quick Start for SNMP Management and Network Hardware InstallationTopology OverviewFeatures 1 Install the switch in a rack or on a shelf Installation and Setup2 Plug the switch in and turn the power on 4 Is setup complete?Port status LEDs Using the SwitchConsole Mgmt Management status LEDsCabling Requirements UTP requirementsFiber optic requirements Connector pinouts Straight-throughvs. crossover cablesDetermining which cable to use Configuring the 100 Mbps workgroup environment Typical Configurations100 Mbps clients using 100 Mbps clients usingor Switch of Configuring the Wide Area Network WAN environmentSwitches BackboneSwitching Hub Connecting to a 10 Mbps segmentServer equipped with two adapters, one atExcessive flow control problems Repeater count limitationsBy default, flow control is enabled on all ports Page Managing the Switch Configuring andAccessing the Console Manager Accessing the Console Manager remotelyConsole Mgmt Entering commands Using the Console ManagercP at the prompt Console Manager command groups Configuring a port for full duplexCommands used To configure a port for full duplex Configuring the SNMP agent for IPCommands used To configure the SNMP agentMonitoring traffic Commands usedTo check traffic on a port Creating VLANs To create a VBD To create an SVLANCreating custom filters Configuring the spanning treeTo set a custom filter Console Command Referencehelp-kbd loginbanner clearlogout System commandsset-prompt set-passwdwarm-reset cold-resetsys-stat init-nvram get-last-errset-line-slip set-sw-fileset-par-file IP commandsset-fg-param start-fgget-ip IP Configurationget-ip-conf set-ipset-bootp get-bootpset-ip-conf get-slipC H A P T E R Address Resolution Protocol ARP Commands ping-stopget-arp-tbl SNMP community strings SNMP commandsset-comm SNMP trap message commandsget-auth set-authSwitching database commands add-trapdel-trap The entry has these properties Configuring and Managing the Switch get-lt-16C H A P T E R find-lt-addr del-lt-entrydel-lt-addr add-lt-entry get-lt-ageset-lt-age Custom filtering get-lt-filteradd-cf-entry get-nv-cftbl del-cf-entryget-nv-cfilt C H A P T E RVLAN commands get-con-matrixget-vbc-matrix del-vbc-domain set-vbc-domainget-vbc-tbl set-sec-vlandel-sec-vlan Spanning tree commandsget-svlan-tbl set-mon-portset-stp get-stpget-st-bcfg get-st-pcfgset-br-fwdel set-br-hellotset-prt-prio set-prt-enbPort configuration commands get-port-cfgset-port-dplex set-port-fctrl Switching statistics commandsclr-cnt get-eth-cntget-colls-cnt get-rmon-cntC H A P T E R packets or bytes received packets forwarded Configuring and Managing the Switch get-mgm-brcntC H A P T E R Console Commands Console command-linesummarySystem Commands IP CommandsIP Commands con’t SNMP CommandsSwitching Database Commands Virtual LAN VLAN Commands Spanning Tree CommandsPort Configuration Commands C H A P T E R Switching Statistics CommandsPage 3 Troubleshooting message A Technical Information Default ConfigurationFeatures SpecificationsPorts Console ManagerGeneral Indicators Status Indicators per portBoot and Configuration Connector Interfaces230 volt configuration 115 volt configurationElectrical Specifications Power Cord SpecificationsSNMP and MIB Support Source Ports Custom Filter Port TableSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 FCC Notice Limited WarrantyManufacturer declaration A p p e n dPage I Index Page Page Page Page Page CompuServe World Wide WebIntel BBS FaxBack