Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 manual Features

Models: 654655-001

1 83

Download 83 pages 573 b

Page 8

C H A P T E R

1 Intel Express 100BASE-TX Switching Hub

Security features include the creation of custom filters and virtual networks (VLANs). You can define any custom filter based on multicast/broadcast, source port, destination port, and destination address. VLAN features include the ability to set broadcast or multicast domains. See Chapter 2 for information on configuring VLANs.

The switch also has a built-in SNMP (Simple Network Management Protocol) agent and can be monitored and controlled through any SNMP-compliant Network Management System (NMS). See page 20 for information on using the switch with an SNMP NMS and getting the switch’s MIB (Management Information Base) file.

Features

•Five RJ-45 Fast Ethernet ports

•Two expansion ports for optional 100BASE-TX or 100BASE-FX media adapters

•Standard 19-inch rack-mount chassis (rack-mount kit included)

•Auto-ranging power supply (automatically adjusts to any voltage between 90 VAC and 264 VAC at 50/60 Hz)

•Full duplex selectable on each port

•Flow control selectable on each port

•1024 address cache entries

•Custom filtering table

•Serial console port with password protection

•SNMP support (see Appendix A for MIB information)

•Spanning tree protocol support

•Built-in remote monitoring (RMON) support (Group 1)

4

Image 8

Intel 654655-001 manual Features

Contents

Intel Express 100BASE-TXSwitching Hub User GuideFirst edition Contents Hardware Installation and Network TopologyConfiguring and Managing the Switch Quick StartTroubleshooting ChapterAppendix A Technical InformationQuick Start Console MgmtOptional Quick Start for SNMP Management Hardware Installation and NetworkTopology OverviewFeatures Installation and Setup 1 Install the switch in a rack or on a shelf2 Plug the switch in and turn the power on 4 Is setup complete?Using the Switch Port status LEDsManagement status LEDs Console MgmtFiber optic requirements Cabling RequirementsUTP requirements Determining which cable to use Connector pinoutsStraight-throughvs. crossover cables Typical Configurations Configuring the 100 Mbps workgroup environment100 Mbps clients using 100 Mbps clients usingConfiguring the Wide Area Network WAN environment or Switch ofSwitches BackboneConnecting to a 10 Mbps segment Switching HubServer equipped with two adapters, one atBy default, flow control is enabled on all ports Excessive flow control problemsRepeater count limitations Page Configuring and Managing the SwitchConsole Mgmt Accessing the Console ManagerAccessing the Console Manager remotely Using the Console Manager Entering commandscP at the prompt Commands used Console Manager command groupsConfiguring a port for full duplex Configuring the SNMP agent for IP To configure a port for full duplexCommands used To configure the SNMP agentTo check traffic on a port Monitoring trafficCommands used Creating VLANs To create an SVLAN To create a VBDConfiguring the spanning tree Creating custom filtersConsole Command Reference To set a custom filterlogin help-kbdbanner clearSystem commands logoutset-prompt set-passwdsys-stat warm-resetcold-reset get-last-err init-nvramset-line-slip set-sw-fileIP commands set-par-fileset-fg-param start-fgIP Configuration get-ipget-ip-conf set-ipget-bootp set-bootpset-ip-conf get-slipC H A P T E R get-arp-tbl Address Resolution Protocol ARP Commandsping-stop SNMP commands SNMP community stringsSNMP trap message commands set-commget-auth set-authdel-trap Switching database commandsadd-trap The entry has these properties C H A P T E R Configuring and Managing the Switchget-lt-16 del-lt-addr find-lt-addrdel-lt-entry set-lt-age add-lt-entryget-lt-age add-cf-entry Custom filteringget-lt-filter del-cf-entry get-nv-cftblget-nv-cfilt C H A P T E Rget-vbc-matrix VLAN commandsget-con-matrix set-vbc-domain del-vbc-domainget-vbc-tbl set-sec-vlanSpanning tree commands del-sec-vlanget-svlan-tbl set-mon-portget-stp set-stpget-st-bcfg get-st-pcfgset-br-hellot set-br-fwdelset-prt-prio set-prt-enbset-port-dplex Port configuration commandsget-port-cfg Switching statistics commands set-port-fctrlclr-cnt get-eth-cntC H A P T E R get-colls-cntget-rmon-cnt packets or bytes received packets forwarded C H A P T E R Configuring and Managing the Switchget-mgm-brcnt Console command-linesummary Console CommandsSystem Commands IP CommandsSwitching Database Commands IP Commands con’tSNMP Commands Port Configuration Commands Virtual LAN VLAN CommandsSpanning Tree Commands Switching Statistics Commands C H A P T E RPage 3 Troubleshooting message Default Configuration A Technical InformationSpecifications FeaturesPorts Console ManagerStatus Indicators per port General IndicatorsBoot and Configuration Connector Interfaces115 volt configuration 230 volt configurationElectrical Specifications Power Cord SpecificationsSNMP and MIB Support Custom Filter Port Table Source PortsSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 Limited Warranty FCC NoticeManufacturer declaration A p p e n dPage I Index Page Page Page Page Page World Wide Web CompuServeIntel BBS FaxBack