Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 manual Status Indicators per port, General Indicators, Boot and Configuration

Models: 654655-001

1 83

Download 83 pages 573 b

Page 67

A p p e n d i x

A

Technical Information

Status Indicators (per port)

Displays Link, Transmit, Receive, Collision, Flow Control/Full Duplex, Management.

General Indicators

Displays Management activity, SNMP presence, power supply status, device failure detection.

Boot and Configuration

NVRAM configuration loaded on power up and fully downloadable. Firmware local or remote downloadable.

Connector Interfaces

UTP RJ-45 (MDI pin configuration)

RS232

SC fiber optic (on optional 100BASE-FX media adapter)

Maximum Cabling Distances

Switch to switch or switch to NIC:

Category 5 UTP: 328 feet (100 meters)

62.5/125µ multimode fiber: 1.2 miles (2 km) at full duplex 1351 feet (412 meters) at half duplex

Switch to repeater:

Category 5 UTP: 328 feet (100 meters)

62.5/125µ multimode fiber: Varies, ~1050 feet (320 meters) total network diameter

Standards Supported

100BASE-TX Fast Ethernet

100BASE-FX Fast Ethernet

FDSE (Full Duplex Switched Ethernet)

IEEE 802.3u (Fast Ethernet)

IEEE 802.1d (Spanning Tree)

SNMP (RFC 1157, etc.)

MIB II (RFC 1213, etc.)

Bridge MIB (RFC 1493)

63

Image 67

Intel 654655-001 manual Status Indicators per port, General Indicators, Boot and Configuration, Connector Interfaces

Contents

User Guide Intel Express 100BASE-TXSwitching HubFirst edition Quick Start ContentsHardware Installation and Network Topology Configuring and Managing the SwitchTechnical Information TroubleshootingChapter Appendix AConsole Mgmt Quick StartOptional Quick Start for SNMP Management Overview Hardware Installationand Network TopologyFeatures 4 Is setup complete? Installation and Setup1 Install the switch in a rack or on a shelf 2 Plug the switch in and turn the power onPort status LEDs Using the SwitchConsole Mgmt Management status LEDsUTP requirements Cabling RequirementsFiber optic requirements Straight-throughvs. crossover cables Connector pinoutsDetermining which cable to use 100 Mbps clients using Typical ConfigurationsConfiguring the 100 Mbps workgroup environment 100 Mbps clients usingBackbone Configuring the Wide Area Network WAN environmentor Switch of Switchesadapters, one at Connecting to a 10 Mbps segmentSwitching Hub Server equipped with twoRepeater count limitations Excessive flow control problemsBy default, flow control is enabled on all ports Page Managing the Switch Configuring andAccessing the Console Manager remotely Accessing the Console ManagerConsole Mgmt Entering commands Using the Console ManagercP at the prompt Configuring a port for full duplex Console Manager command groupsCommands used To configure the SNMP agent Configuring the SNMP agent for IPTo configure a port for full duplex Commands usedCommands used Monitoring trafficTo check traffic on a port Creating VLANs To create a VBD To create an SVLANCreating custom filters Configuring the spanning treeTo set a custom filter Console Command Referenceclear loginhelp-kbd bannerset-passwd System commandslogout set-promptcold-reset warm-resetsys-stat set-sw-file get-last-errinit-nvram set-line-slipstart-fg IP commandsset-par-file set-fg-paramset-ip IP Configurationget-ip get-ip-confget-slip get-bootpset-bootp set-ip-confC H A P T E R ping-stop Address Resolution Protocol ARP Commandsget-arp-tbl SNMP community strings SNMP commandsset-auth SNMP trap message commandsset-comm get-authadd-trap Switching database commandsdel-trap The entry has these properties get-lt-16 Configuring and Managing the SwitchC H A P T E R del-lt-entry find-lt-addrdel-lt-addr get-lt-age add-lt-entryset-lt-age get-lt-filter Custom filteringadd-cf-entry C H A P T E R del-cf-entryget-nv-cftbl get-nv-cfiltget-con-matrix VLAN commandsget-vbc-matrix set-sec-vlan set-vbc-domaindel-vbc-domain get-vbc-tblset-mon-port Spanning tree commandsdel-sec-vlan get-svlan-tblget-st-pcfg get-stpset-stp get-st-bcfgset-prt-enb set-br-hellotset-br-fwdel set-prt-prioget-port-cfg Port configuration commandsset-port-dplex get-eth-cnt Switching statistics commandsset-port-fctrl clr-cntget-rmon-cnt get-colls-cntC H A P T E R packets or bytes received packets forwarded get-mgm-brcnt Configuring and Managing the SwitchC H A P T E R IP Commands Console command-linesummaryConsole Commands System CommandsSNMP Commands IP Commands con’tSwitching Database Commands Spanning Tree Commands Virtual LAN VLAN CommandsPort Configuration Commands C H A P T E R Switching Statistics CommandsPage 3 Troubleshooting message A Technical Information Default ConfigurationConsole Manager SpecificationsFeatures PortsConnector Interfaces Status Indicators per portGeneral Indicators Boot and ConfigurationPower Cord Specifications 115 volt configuration230 volt configuration Electrical SpecificationsSNMP and MIB Support Source Ports Custom Filter Port TableSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 A p p e n d Limited WarrantyFCC Notice Manufacturer declarationPage I Index Page Page Page Page Page FaxBack World Wide WebCompuServe Intel BBS