Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 manual Switching statistics commands, set-port-fctrl, clr-cnt, get-eth-cnt

Models: 654655-001

1 83

Download 83 pages 573 b

Page 54

C H A P T E R 2 Intel Express 100BASE-TX Switching Hub

set-port-fctrl

set-port-fctrl <port-number> {onoff}

Turns the flow control feature on or off for the specified port. The default is on.

If the port is in full-duplex mode, flow control is automatically off. If you try to set it to ON while full-duplex is enabled, the Console Manager ignores the change after a reset. Flow control or full duplex can be active, or neither, but not both.

SYS_console> set-port-fctrl 2 off

Port 2 - flow control <off>

Parameter change in NVRAM OK

Switching statistics commands

This section contains instructions for displaying switching statistics using the Console Manager. The following commands provide full physical layer information as well as interport switching statistics.

clr-cnt

Clears (resets) the Ethernet and bridging statistical counters.

get-eth-cnt

get-eth-cnt <port-number>

Displays the Ethernet Statistics Counters for port port-number. This is almost identical to the Ethernet-like Statistics Group of the Ethernet MIB.

SYS_console> get-eth-cnt 3 Ethernet Statistics for port 3

=================================

Transmit	OK	:	1427908
Underflow	Errors:		153
Exces Coll	Errors:		0
Exces Fctrl Errors:			0
Receive	EOF	:	1443206
Receive	OK	:	1443192
Overflow	Errors:		2
CRC	Errors:		9
Alignment	Errors:		0
Runt	Errors:		6
Lost/Fctrl	Errors:		0
Too Long	Errors:		0

=================================

50

Image 54

Intel 654655-001 manual Switching statistics commands, set-port-fctrl, clr-cnt, get-eth-cnt

Contents

Intel Express 100BASE-TXSwitching Hub User GuideFirst edition Configuring and Managing the Switch ContentsHardware Installation and Network Topology Quick StartAppendix A TroubleshootingChapter Technical InformationQuick Start Console MgmtOptional Quick Start for SNMP Management Topology Hardware Installationand Network OverviewFeatures 2 Plug the switch in and turn the power on Installation and Setup1 Install the switch in a rack or on a shelf 4 Is setup complete?Using the Switch Port status LEDsManagement status LEDs Console MgmtCabling Requirements UTP requirementsFiber optic requirements Connector pinouts Straight-throughvs. crossover cablesDetermining which cable to use 100 Mbps clients using Typical ConfigurationsConfiguring the 100 Mbps workgroup environment 100 Mbps clients usingSwitches Configuring the Wide Area Network WAN environmentor Switch of BackboneServer equipped with two Connecting to a 10 Mbps segmentSwitching Hub adapters, one atExcessive flow control problems Repeater count limitationsBy default, flow control is enabled on all ports Page Configuring and Managing the SwitchAccessing the Console Manager Accessing the Console Manager remotelyConsole Mgmt Using the Console Manager Entering commandscP at the prompt Console Manager command groups Configuring a port for full duplexCommands used Commands used Configuring the SNMP agent for IPTo configure a port for full duplex To configure the SNMP agentMonitoring traffic Commands usedTo check traffic on a port Creating VLANs To create an SVLAN To create a VBDConfiguring the spanning tree Creating custom filtersConsole Command Reference To set a custom filterbanner loginhelp-kbd clearset-prompt System commandslogout set-passwdwarm-reset cold-resetsys-stat set-line-slip get-last-errinit-nvram set-sw-fileset-fg-param IP commandsset-par-file start-fgget-ip-conf IP Configurationget-ip set-ipset-ip-conf get-bootpset-bootp get-slipC H A P T E R Address Resolution Protocol ARP Commands ping-stopget-arp-tbl SNMP commands SNMP community stringsget-auth SNMP trap message commandsset-comm set-authSwitching database commands add-trapdel-trap The entry has these properties Configuring and Managing the Switch get-lt-16C H A P T E R find-lt-addr del-lt-entrydel-lt-addr add-lt-entry get-lt-ageset-lt-age Custom filtering get-lt-filteradd-cf-entry get-nv-cfilt del-cf-entryget-nv-cftbl C H A P T E RVLAN commands get-con-matrixget-vbc-matrix get-vbc-tbl set-vbc-domaindel-vbc-domain set-sec-vlanget-svlan-tbl Spanning tree commandsdel-sec-vlan set-mon-portget-st-bcfg get-stpset-stp get-st-pcfgset-prt-prio set-br-hellotset-br-fwdel set-prt-enbPort configuration commands get-port-cfgset-port-dplex clr-cnt Switching statistics commandsset-port-fctrl get-eth-cntget-colls-cnt get-rmon-cntC H A P T E R packets or bytes received packets forwarded Configuring and Managing the Switch get-mgm-brcntC H A P T E R System Commands Console command-linesummaryConsole Commands IP CommandsIP Commands con’t SNMP CommandsSwitching Database Commands Virtual LAN VLAN Commands Spanning Tree CommandsPort Configuration Commands Switching Statistics Commands C H A P T E RPage 3 Troubleshooting message Default Configuration A Technical InformationPorts SpecificationsFeatures Console ManagerBoot and Configuration Status Indicators per portGeneral Indicators Connector InterfacesElectrical Specifications 115 volt configuration230 volt configuration Power Cord SpecificationsSNMP and MIB Support Custom Filter Port Table Source PortsSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 Manufacturer declaration Limited WarrantyFCC Notice A p p e n dPage I Index Page Page Page Page Page Intel BBS World Wide WebCompuServe FaxBack